SAFETY-02: a loop can be fresh, tracking and inside its rating and still push the wrong way

The stale-input watchdog asks whether the meter is still talking. The saturation
freeze asks whether the inverter can follow. The output clamp asks whether the
number is too big. A loop can pass all three while charging the battery out of
the grid, because the only thing wrong is the sign.

On 2026-08-20 a commercial controller did exactly that four times in one day,
for up to 77 minutes at a stretch, reaching a commanded -14 768 W against a
±5000 W inverter. app/watchdog.py compares the emitted setpoint against the
authoritative P1 figure and, when they oppose each other with both over 300 W
for 180 s continuously, files a failsafe SET claim at P_SAFETY, commands 0 W and
latches there until an operator starts control again.

Validated against that day rather than against an argument: sim/replay_sign.py
in the infra repo drives this module over the committed captures of both
2026-08-20 and the healthy 2026-08-23 and reaches 18 trips on the fault day -
every one inside a window NOTES.md §4.7 accounts for - and 0 on the healthy day.
The four episodes do share one signature: 0.3 / 0.9 / 10.5 / 0.0 % sign
agreement inside them against 92.9 % healthy.

Three decisions the ticket could not make:

- It is DISARMED whenever the grid-following loop is not what is driving. Sign
  agreement is a property of a loop that follows the meter, and a maintenance
  grid charge opposes the meter by design - 2500 W of charge into a house
  drawing 500 W is +3000 W on the meter against a -2500 W command, for hours.
  The gate tests the emitted number, not the winning claim's name, because a
  limit claim can let the loop "win" and still replace its value.
- The trip LATCHES. Commanding 0 W removes the command side of the comparison,
  so the disagreement always clears the moment the trip works.
- sign_disagree_w at or above max_w is refused at startup. The arbiter never
  lets a command exceed max_w, so such a threshold leaves the watchdog incapable
  of firing while the status page still reports it armed.

What it does not catch, said out loud: an inverter that ACTS opposite to its
command moves the meter further the same way, leaving command and meter in
agreement. That is the saturation freeze's job.

Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01Du77usMj8XNKNFZGmUiWDa

.gitattributes

@@ -0,0 +1,10 @@
+# This add-on is deployed to a Linux container. core.autocrlf=true on the
+# authoring box gave the checkout CRLF, so a plain copy shipped CRLF files -
+# run.sh with CRLF is a "bad interpreter" failure, and any hash-based drift
+# check between repo and deployment fails for a reason that has nothing to do
+# with the code. Deploy with:
+#     git -c core.autocrlf=false archive release/1.0 goodwe_controller | tar -x
+# which is how 0.3.0 went out, byte-identical to the blobs.
+* text=auto eol=lf
+*.png binary
+*.gz  binary

HANDOVER.md

@@ -12,7 +12,7 @@ a GoodWe GW5000S-BP.
 
 | | |
 |---|---|
-| running | `local_goodwe_controller` **0.2.0**, `boot: auto`, holding grid at zero |
+| running | `local_goodwe_controller` **0.4.0**, `boot: auto`, holding grid at zero |
 | installed as | a **Local** add-on: `/addons/goodwe_controller` on HA OS at 192.168.2.158 |
 | repo | Gitea `admin/goodwe-addon` (ssh://git@192.168.2.147:2222) — **private** |
 | tuning | gain 0.6, `max_w` 5000, slew 1000, deadband 15, step 10, saturation 500/3, heartbeat 10 s |
@@ -52,9 +52,26 @@ Run the checks before deploying. No framework needed:
 
 ```bash
 cd goodwe_controller
-python3 test_control.py && python3 test_maintenance.py && python3 test_arbiter.py
+python3 test_control.py && python3 test_maintenance.py && python3 test_arbiter.py \
+  && python3 test_validate.py && python3 test_p1.py && python3 test_watchdog.py \
+  && python3 test_loop.py
 ```
 
+`test_watchdog.py` covers SAFETY-02's logic and its trip path. Its headline
+validation is not here at all: `sim/replay_sign.py` in the infra repo drives the
+same module over the two captured RS485 days and must fire on all four of the
+2026-08-20 episodes and stay silent on 2026-08-23. That needs both checkouts —
+`GOODWE_ADDON_REPO=/path/to/goodwe-addon python3 sim/replay_sign.py`.
+
+⚠️ `test_loop.py` takes about **95 seconds** (measured 93 s) and that is not a bug. It
+drives the real control loop, which sleeps 1 s a tick, eight times over, to prove a
+wall-clock property about it (SAFETY-12); mocking the clock there would leave the
+assertion testing the mock. The other six suites together are ~440 checks and finish in
+seconds — `test_watchdog.py` spends ~3 s of that driving a real `Controller` through a
+trip. If you shorten `test_loop.py`'s windows, re-measure and correct this figure —
+an understated runtime is what makes a slow test look like a hung one, and a slow test
+that looks hung gets deleted.
+
 ---
 
 ## 3. Known broken / unfinished

goodwe_controller/CHANGELOG.md

@@ -1,5 +1,378 @@
 # Changelog
 
+## 0.5.0
+
+**SAFETY-02 — the sign-disagreement watchdog.** The add-on now watches whether
+the setpoint it is emitting and the grid figure it is regulating on point the
+same way. If they oppose each other, both over `sign_disagree_w` (300 W), for
+`sign_disagree_s` (180 s) **continuously**, it files a failsafe claim at
+`P_SAFETY`, commands **0 W**, and latches there until an operator starts control
+again. New module `app/watchdog.py`; new options `sign_disagree_w` and
+`sign_disagree_s`.
+
+This is the gap the existing failsafes leave open. The stale-input watchdog asks
+whether the meter is still talking, the saturation freeze asks whether the
+inverter can follow, the output clamp asks whether the number is too big — a
+loop can pass all three while charging the battery out of the grid, because the
+only thing wrong is the sign. On 2026-08-20 a commercial controller did exactly
+that four times in one day, for up to 77 minutes at a stretch, and reached a
+commanded −14 768 W against a ±5000 W inverter.
+
+Validated against that day. `sim/replay_sign.py` in the infra repo drives this
+module over the committed RS485 captures of both 2026-08-20 (the four episodes)
+and 2026-08-23 (healthy): **18 trips on the fault day, every one inside a window
+`NOTES.md` §4.7 accounts for, and 0 on the healthy day.** The four episodes do
+share one signature rather than merely resembling each other — sign agreement
+runs 0.3 / 0.9 / 10.5 / 0.0 % inside them against 92.9 % on the healthy day.
+
+Three decisions worth knowing about:
+
+- **It is disarmed whenever the grid-following loop is not what is driving.**
+  Sign agreement is a property of a loop that follows the meter. A maintenance
+  grid charge opposes the meter *by design* — 2500 W of charge into a house
+  drawing 500 W is +3000 W on the meter against a −2500 W command, for hours —
+  and armed unconditionally this would trip on every maintenance cycle. The gate
+  tests the emitted number, not the winning claim's name: a limit claim can let
+  the loop "win" and still replace its value with one pointing the other way.
+- **The trip latches.** Commanding 0 W removes the command side of the
+  comparison, so the disagreement always clears the moment the trip works.
+  Un-latched, this would trip, clear, and hand the actuator back to the loop that
+  was driving the wrong way, every three minutes forever.
+- **`sign_disagree_w` at or above `max_w` is refused at startup** (validator rule
+  5). The arbiter never lets a command exceed `max_w`, so such a threshold makes
+  the watchdog incapable of firing while the status page still reports it armed.
+  A disarmed guard that advertises itself as armed is the failure mode this
+  project keeps refusing to ship.
+
+What it does **not** catch, stated so nobody assumes otherwise: an inverter that
+acts opposite to what it was told moves the meter *further* the same way, so
+command and meter agree while everything runs away. That is the saturation
+freeze's job, which compares the command against the battery's actual power.
+
+`test_validate.py`'s "the smallest sane max_w still starts" case now names a
+reachable sign threshold, because a 1 W ceiling genuinely does disarm the 300 W
+default and is now correctly refused.
+
+## 0.4.0
+
+**CFG-01.** The add-on now refuses to start on a configuration it cannot honour,
+instead of logging a line and carrying on. `validate_startup_config()` runs in
+`amain()` before the broker, the web server or any task exists, so a refusal
+cannot leave half a controller running behind a UI.
+
+It refuses only where continuing produces one of two outcomes: **(a)** a stated
+limit is untrue - the operator configured a bound and a lower layer silently
+enforces a different one - or **(b)** the add-on is inert and indistinguishable
+from healthy. (b) is not a special case of (a): with no `setpoint_entity`, layer
+1 pinning the inverter at 0 W is the failsafe *working*. The system does not
+become unsafe, it becomes a convincing impression of a working controller.
+
+Four things qualify:
+
+- **`max_w` above (or below) the setpoint device's own rating.** This is the one
+  that changed behaviour. It used to warn `the device wins` and run anyway, with
+  `write_setpoint()` silently clamping, so the configured ceiling was never the
+  real one and the only evidence had scrolled off the log. The refusal names the
+  configured value, the device's value, and which wins.
+- **No `setpoint_entity`.** A controller with no actuator: every write is a
+  no-op, the device rating is never read, and the ESP32 heartbeat that holds off
+  the layer-1 failsafe never happens. It ran, looked healthy, and moved nothing.
+- **A `meter_source` that can never produce a reading** - missing `p1_host`,
+  missing `p1_net_entity`, a blank MQTT topic, a phase list disagreeing with
+  `meter_phases`, an unknown source name, or a `meter_poll_s` at or past
+  `meter_max_age_s`. These were already caught, but they only *disabled
+  ingestion*, which leaves the grid reading None forever: permanent "inputs
+  missing", 0 W, and a status page indistinguishable from a healthy meter nobody
+  has sent anything to yet.
+- **`meter_max_age_s` above the firmware's ingest veto.** The schema accepts
+  `int(5,300)`; the ESP32's threshold is a compile-time `max_age_s: "30"` and it
+  trips layer 1 at `p1_age_s >= 30`. Set 120 and the add-on treats a 119 s
+  reading as fresh and keeps commanding, while the firmware has already vetoed
+  and is holding the inverter at 0 W - healthy meter, running controller,
+  nothing moving, and no line anywhere saying the number you set was overruled.
+  Structurally the same fault as the `max_w` case. Only *above* the veto is
+  refused: below it the add-on gives up first, which is fail-safe and visible on
+  its own status page. Mirrored as `validate.FIRMWARE_INGEST_VETO_S` - it cannot
+  be imported from a compile-time YAML substitution, so it carries a note about
+  the one direction in which it can go stale.
+
+`max_w` at or below zero is refused too. Schema-blocked on a real install, but
+`validate_startup_config()` is now also the simulation suite's entry point, and
+a non-positive `max_w` inverts the arbiter's `supervised` bounds into a
+contradiction that resolves to 0 W - i.e. it would read as a safety trip rather
+than as the typo it is.
+
+The predicates for the meter group still live in `p1.validate_meter_options()`,
+which `build_source()` also calls - one definition, two callers, not two
+competing validators. Two transports gained a check they never had: `ha_dsmr`
+with only one of its two entities, and `mqtt_p1` with a blank topic, both of
+which previously built a transport that could never read.
+
+Deliberately **not** refused, because it is untidy rather than unsafe:
+`integrator_max_w` above `max_w` (the arbiter still bounds the wire to ±max_w,
+so the cost is unwind latency, not amperage - warned), a missing `soc_entity` /
+`batt_entity` (fail-safe, and already a red NOT READY banner naming it), a
+`setpoint_entity` that has not appeared on the Core API yet (ESPHome is routinely
+late; refusing would make a slow boot need a human - re-checked once the real
+rating arrives), and a thin-but-nonzero `meter_poll_s` margin.
+
+A refusal is legible as a refusal: a banner that says in words that this is a
+configuration problem and nothing is broken, the numbered problems, no traceback,
+and exit status 78 (`EX_CONFIG`).
+
+**SAFETY-12.** The control loop now evaluates on a clock as well as on a change.
+`run_control()` ran `cycle()` only when the meter value differed from the
+previous poll, so a meter that repeated a value ran **no control cycles at
+all** - while the heartbeat went on re-emitting the last command and the
+firmware went on putting it on the wire every 2 s. Layer 1 stayed fed, every
+indicator read healthy, and a command computed from an old reading kept being
+executed through whatever the load did next. Measured on the rig during TEL-05:
+70 s at a literally constant 350.0 W with 14 arrivals and zero cycles.
+
+**It was worse than a latency limit: it was a safety claim that could not
+fire.** `stale_input_s` and the `inputs missing -> 0 W` claim both live *inside*
+`cycle()`. Pre-fix, if the meter value happened to be constant, `cycle()` was
+never called again - so that claim had no way to run. Constant meter, SoC entity
+dying at t=4 s, same binary:
+
+```
+pre-fix    writes: [(0.0, 220.0), (0.0, 220.0), (10.1, 220.0)]
+           final target: 220.0 W   reason: 'loop -> 220 W'
+post-fix   writes: [(0.0, 220.0), (0.0, 220.0), (3.0, 430.0), (9.1, 0.0), (10.1, 0.0)]
+           final target: 0.0 W     reason: 'safety -> 0 W'
+```
+
+The pre-fix controller held 220 W through the entire input outage with its
+status line still reading `loop -> 220 W`, and layer 1 does not cover that case
+on a `meter_source: off` install: no P1 age sensor is published, so the firmware
+has nothing to veto on, while the heartbeat keeps its watchdog fed. So the old
+behaviour was not "holds a stale command safely" - it was a failsafe that a
+repeating meter switched off. `test_loop.py` asserts both halves.
+
+`cycle_floor_s` (default **15 s**) is a deadline on the gap between cycles, not
+a second scheduler: every cycle resets it, whichever trigger fired. On a healthy
+meter it never elapses, so the cycle rate, the write sequence and therefore the
+per-cycle gain the tuning was measured against are unchanged - asserted in
+`test_loop.py` by driving the real loop twice on one binary (a huge
+`cycle_floor_s` reproduces the old behaviour exactly) and comparing the
+commanded values.
+
+The reset is not the only thing holding that up, and the other argument is the
+sturdier one: the combined cycle rate is `max(arrival rate, 1/floor)`, never the
+sum. At 1/15 s the floor is strictly slower than the ~1/5 s arrival rate, so
+even a hypothetical floor racing the arrivals could not exceed the nominal
+healthy rate. The re-tune is unreachable by construction. ⚠️ That holds only
+while `cycle_floor_s` stays above the meter's update interval, and the schema
+minimum is 5 s - which is exactly the reference meter's interval. Nothing
+enforces the relationship; `validate.py` is the obvious home for it and does not
+have it yet.
+
+Observed over six real minutes on the same rig, one binary, meter held at a
+literally constant 350.0 W: **before, 1 cycle** (at startup) and then nothing,
+the command stuck at 220 W against a 350 W import for the rest of the window.
+**After, 24 cycles**, worst gap 15.14 s, and the ordinary PI ramp doing its job -
+220, 430, 650, 860, 1080, 1300, 1510, 1730, 1940, 2000 W, one step per cycle,
+rail at t=136 s and flat after. Three minutes with the meter parked at the
+target instead: **1 cycle before, 12 after, and 19 writes either way - the same
+19**. Three minutes on a normally-changing meter: **36 cycles and 49 writes on
+both sides, the same values in the same order.** The heartbeat write count never
+moves; the only writes the fix adds are the ten the loop was supposed to be
+making all along.
+
+15 s is bracketed, not round.
+
+**Below it, ~11 s, and it arises more routinely than a dropped poll.**
+`HomeWizardLocalSource` polls at 5.0 s against a meter that updates every 4.97 s
+(NOTES.md:640). Two near-equal periods beat, so roughly once every ~14 minutes
+the poller steps over an update entirely - a ~10 s gap between changed values on
+a perfectly healthy meter, plus up to 1 s for the 1 s tick to notice. A failed
+HTTP poll (retried on the next tick, no backoff) adds another 5 s. The floor
+sits above the beat-skip so it does not fire on that alone; what it takes to
+reach 15 s is a beat-skip *and* a failed poll coinciding.
+
+**Above it, 30 s.** `meter_max_age_s` is 30 s, past which there is no reading to
+evaluate, and the firmware's ingest veto is also 30 s - so the loop is
+guaranteed to have re-decided at least twice inside any window in which layer 1
+might otherwise be the only thing deciding. ⚠️ The default is therefore not
+independently justified at 15: if the firmware's veto ever moves, this moves
+with it. Noted beside the constant in `main.py`.
+
+It is also exactly `stale_input_s`, this system's existing answer to "how long
+may we hold without re-deciding".
+
+A floor cycle runs the **full** law on the same inputs, integrator included. In
+P1 mode the freshness question is already answered upstream and answered harder
+- past `meter_max_age_s` the reading is None, which is "inputs missing", which
+is a `P_SAFETY` 0 W claim - so a floor cycle there can only ever run on a reading
+this system already calls fresh. ⚠️ That is transport-conditional: with
+`meter_source: off`, `read_inputs()` takes the grid figure straight from
+`hass.number()` with **no age gate at all**, so a Home Assistant entity that has
+gone quiet reads as current on that path, with or without this change. Running
+the full law is still right there - the alternative is a degraded second law
+reasoning about an age nobody measured - but the floor does not make that path
+fresh. The integrator advances per *cycle*, not per second,
+so bounding the gap bounds the accumulation; `integrator_max_w` bounds it after
+that. A gentler second law for floor cycles would be a second set of dynamics
+nobody can test on this hardware.
+
+⚠️ **This is not a freeze detector**, and TEL-05 established one cannot be built
+here: at the converged -10 W target a 1 Wh register needs ~6 minutes to move
+while the power figure legitimately repeats, so any threshold on `unchanged_s`
+false-trips at the exact operating point we run at. Nothing in this change
+decides whether a repeated reading is *true*. It stops "the number is the same"
+from meaning "do not think". The consequence, stated plainly: against a meter
+genuinely frozen at a wrong value the loop will now correct toward that wrong
+value rather than hold a stale command, bounded by `max_w`, the arbiter and the
+device rating. That was already what happened to a lying meter whose value
+merely jittered; bit-exact repetition was never a safety property.
+
+`DOCS.md`'s "Saturation is counted in cycles, not seconds" section documented
+the old behaviour as an accepted deviation. It is **qualified, not deleted**:
+the deviation survives (the window is still counted in cycles, and 3 x 15 s is
+still not the specification's 10 s) but it is now bounded at 45 s instead of
+open-ended, and the passage's second justification - "nothing accumulates while
+it is stalled" - is called out as having covered integrator windup and not
+staleness, which was the actual hazard. The same wrong argument in
+`control.py`'s saturation comment is corrected too.
+
+**TEL-04.** `meter_source: ha_signed` reads a single *signed* power entity, which
+is the shape a HomeWizard P1 publishes. Both transports 0.3.0 shipped require two
+unsigned registers and refuse negatives, so neither fits the meter installed here.
+
+**TEL-05.** `meter_source: homewizard_local` polls the meter's own local API
+directly. This exists because of something the HA paths cannot do: Home Assistant
+fires no state change for a repeated reading and exposes no arrival signal at
+all, so `sensor.p1_sample_age_s` on those transports measures time since the
+*value changed*, not since the meter *reported*. Real captured data has gaps of
+42 s and 97 s between changes on a perfectly healthy meter - long enough for a
+30 s staleness threshold to command 0 W for no reason. Every HTTP response to the
+local API is a genuine arrival, so the age means what it says.
+
+Verified on the rig against a literally constant 350.0 W for 70 s - the exact
+state where the HA path recorded zero samples in 45 s - with 14 arrivals and the
+age never exceeding the poll cadence.
+
+Set `p1_host` to the meter's address and `meter_poll_s` (default 5 s, matching
+the meter's own ~5 s update). Still defaults to `off`; nothing changes for an
+install that does not opt in.
+
+Freeze detection is separate and deliberately not thresholded: a meter answering
+200 OK with a stale number *is* arriving, so no arrival stamp can flag it. The
+energy registers carry that as `unchanged_s`, surfaced on the status line for a
+human to read rather than alarmed on - at a converged -10 W a 1 Wh register needs
+about six minutes to move, so any threshold would false-trip at the target
+operating point.
+
+## Unreleased
+
+**TEL-05.** A fourth `meter_source`, `homewizard_local`, which polls a
+HomeWizard P1's **own local API** (`GET /api/v1/data`) instead of watching a
+Home Assistant entity. Set `p1_host` to the meter's address; `meter_poll_s`
+(default 5 s, the meter's own update rate) sets the cadence.
+
+✅ **This is the first transport whose `sensor.p1_sample_age_s` measures when
+the meter *reported*, and therefore the first one a firmware watchdog may
+threshold.** Every HTTP response is an arrival: the meter answered, now, with
+its current reading, and whether the *number* moved is not consulted. Home
+Assistant cannot express that at all — a repeated reading emits no
+`state_changed`, advances `last_reported` on neither serialiser, and
+`state_reported` is not subscribable ("Event filter is required"). On
+`ha_signed` that made a healthy meter under a flat load indistinguishable from
+a dead one, and our own capture of this house's meter goes 42.2 s and 97.0 s
+between changes — both past the default `meter_max_age_s` of 30, i.e. a false
+trip to 0 W on a meter that is fine. If you have a HomeWizard P1, move to this
+mode.
+
+Everything TEL-01 established is reused, not re-implemented: ingest
+timestamping, `meter_max_age_s`, the clock-recomputed age, the plausibility
+bounds and the §20 unsigned-decode rejection, and the same `split_signed` sign
+convention `ha_signed` uses. A failed or timed-out poll submits nothing, so it
+is a *missing* reading — never 0 W — and it does not reset the age.
+
+Verified on the ENV-01 rig against `sim/hwsim.py`, steady and with `--fault
+freeze` injected. Still defaults to `off`.
+
+⚠️ **An arrival stamp still cannot see a *frozen* meter**, and no arrival
+detector can: a meter answering `200 OK` forever with a stale number is
+arriving. The local API does expose what the HA path never had — the
+`total_power_*_kwh` registers stop advancing — and the transport tracks it as
+`unchanged_s`, but that is deliberately **not** folded into the age and not
+thresholded: this controller regulates grid power toward ~0 W, and at a
+converged −10 W the export register needs six minutes to move by its 1 Wh
+resolution while the power figure legitimately repeats. Thresholding it at 30 s
+would rebuild the false-trip limit cycle at the exact operating point we aim
+for. Freeze detection needs the low-power case solved first, separately. It is
+shown on the status page's P1 line instead — leaving it unthresholded only
+holds up if a human can read it, so now they can.
+
+**TEL-04.** A third `meter_source`, `ha_signed`, reading **one signed** Home
+Assistant entity: positive = import, negative = export. That is the shape a
+HomeWizard P1 publishes (`sensor.p1_meter_active_power`), and it is the meter
+actually fitted here - which neither TEL-01 transport can read, because
+`ha_dsmr` needs two unsigned registers and refuses a negative one, i.e. every
+exporting telegram. Set `p1_net_entity`, and `p1_phase_net_entities` for the
+per-phase capacity-tariff figures on a three-phase connection.
+
+Everything TEL-01 established is inherited rather than re-implemented - the
+new transport is a subclass of the `ha_dsmr` one overriding only which
+entities it wants and how they become a sample. So ingest timestamping,
+`meter_max_age_s`, `sensor.p1_sample_age_s` recomputed against the clock and
+republished once a second, the plausibility bounds, and `unavailable` /
+`unknown` treated as a *missing reading and never 0 W* all behave identically
+across the three sources.
+
+Still defaults to `off`; an existing install is unaffected until it opts in.
+
+⚠️ **`sensor.p1_sample_age_s` is published on `ha_signed`, but must not yet be
+thresholded by the ESP32 stale-input watchdog.** On the HA WebSocket paths the
+age is stamped from `state_changed`, so it measures time since the value
+*changed*, not since the meter *reported* - and Home Assistant exposes no
+arrival signal for a repeated reading (no `state_changed`, no `last_reported`
+movement on either serialiser, and `state_reported` is not subscribable over
+the WebSocket). Measured on the ENV-01 rig against the real HomeWizard
+integration. `ha_dsmr` mostly escapes it because a telegram moves several
+entities at once; `ha_signed` has one, so a healthy meter under a flat load is
+indistinguishable from a dead one. Our own capture has the house meter going
+42.2 s and 97.0 s between changes. Raising `meter_max_age_s` does not fix that,
+it only chooses which error you get; the fix is an arrival stamp from the meter
+itself and is a separate ticket. Full detail in DOCS.md.
+
+## 0.3.0
+
+**SAFETY-04.** The control law's integrator is now an explicit accumulator,
+bounded independently of the output clamp instead of inheriting whatever
+headroom the clamp happened to leave. It also freezes while the inverter is
+not tracking, rather than continuing to wind up against a command nothing is
+acting on. `integrator_max_w` (default `0`) governs the bound; `0` means
+"follow `max_w`", which is the existing behaviour.
+
+Behaviour is unchanged at the defaults - a 4,928-case equivalence sweep
+against the previous control law confirms it decides identically at
+`integrator_max_w: 0`.
+
+**TEL-01.** P1 meter ingestion, so a Belgian P1's two unsigned registers
+(consumption, injection) no longer need a hand-written signed template
+sensor: the subtraction moves into the add-on, done once and tested. Two
+transports, chosen with the new `meter_source` option: `ha_dsmr` subscribes
+to the DSMR integration over the HA WebSocket, `mqtt_p1` reads a topic.
+Defaults to `off`, which keeps the existing `meter_entity` path untouched -
+nothing changes for an install that does not opt in.
+
+Enabling it publishes `sensor.p1_sample_age_s`: seconds since the newest
+accepted telegram, recomputed against the clock and republished roughly once
+a second rather than only when a telegram lands. That is deliberate - Home
+Assistant only pushes a state on change, so a meter sitting at a genuinely
+constant reading would otherwise look identical to a dead one. Watching the
+age instead means a frozen meter shows a climbing age, not a flat line. The
+firmware watchdog subscribes to this exact entity id.
+
+Known limits, both already in DOCS.md: on `mqtt_p1`, a bridge stuck
+republishing its last telegram still "arrives", so the age cannot detect
+that particular failure - prefer `ha_dsmr` where both are available. And a
+dead P1 meter takes 45 s to reach 0 W commanded (30 s for `meter_max_age_s`
+to call the reading stale, then 15 s of `stale_input_s` on top), which is
+`meter_max_age_s` and `stale_input_s` stacking, not either one alone.
+
 ## 0.2.1
 
 `target_grid_w` (default -10 W): what the meter should rest at. The deadband

goodwe_controller/DOCS.md

@@ -24,6 +24,9 @@ The inverter **holds its last command forever** — it has no meter-timeout. So:
   commanding it.
 - This add-on commands 0 W when its inputs go missing, when you stop control,
   and when it shuts down.
+- This add-on commands 0 W **and latches there** if what it is commanding and
+  what the meter reads point opposite ways for three minutes — see "The
+  sign-disagreement failsafe" below.
 - The **optional RS485 e-stop** is the only thing that covers this machine
   dying. Without it, a failed host leaves the battery latched at its last
   command until someone intervenes.
@@ -51,21 +54,67 @@ phase having charged nothing.
 ### P1 meter ingestion
 
 `meter_entity` above expects one signed sensor, which usually means a template
-someone wrote by hand. A Belgian P1 meter does not publish one: it publishes two
-**unsigned** registers, consumption and injection. Setting `meter_source` moves
-that subtraction into the add-on, where it is done once and tested, and replaces
-`meter_entity` entirely.
+someone wrote by hand. Setting `meter_source` moves the whole derivation into
+the add-on, where it is done once and tested, and replaces `meter_entity`
+entirely.
+
+Which mode you want depends on what your P1 reader publishes, and there are two
+shapes in the wild:
+
+- **Two unsigned registers**, consumption and injection, which is what a Belgian
+  P1 read over DSMR gives you → `ha_dsmr`, or `mqtt_p1` for a bridge. The add-on
+  subtracts them.
+- **One signed figure**, positive = import and negative = export, which is what
+  a HomeWizard P1 gives you (`sensor.p1_meter_active_power`) → `ha_signed`. The
+  add-on splits it. `ha_dsmr` **cannot** read this: it wants two registers and
+  rejects a negative one outright, which is every exporting telegram.
+
+Either way, do not build the missing shape out of template sensors. The point of
+`meter_source` is that the sign convention is derived in one tested place rather
+than in YAML nobody reviews underneath a safety input.
+
+> ✅ **If your meter is a HomeWizard P1, use `homewizard_local`, not
+> `ha_signed`.** It reads the same meter and produces the same numbers, but it
+> polls the meter directly instead of watching a Home Assistant entity — and
+> that is the difference between an age sensor a watchdog can threshold and one
+> it cannot. See "`sensor.p1_sample_age_s`" below; `ha_signed` remains for
+> installs where the meter is only reachable through Home Assistant.
+
+> ⚠️ **`ha_dsmr` and `mqtt_p1` have never processed a telegram from real
+> hardware.** No meter in this installation uses either one. Both were written
+> to the assumption in `specs.md` §5.2 that a Belgian P1 exposes two unsigned
+> registers, and the meter actually fitted here does not — it is the HomeWizard
+> P1 that `ha_signed` reads. They are covered by the unit checks in `test_p1.py`
+> and by an end-to-end test against a fake Home Assistant, and nothing more.
+>
+> This is recorded because the realistic way it bites is someone debugging a
+> meter problem months from now treating those two paths as proven and looking
+> for the fault elsewhere. If you are the first person to point one at a real
+> meter, expect to find something, and please update this note when you do.
 
 | option | default | meaning |
 |---|---|---|
-| `meter_source` | `off` | `off` keeps `meter_entity`. `ha_dsmr` subscribes to the DSMR integration over the HA WebSocket; `mqtt_p1` reads a topic |
+| `meter_source` | `off` | `off` keeps `meter_entity`. `ha_dsmr` subscribes to the DSMR integration over the HA WebSocket; `mqtt_p1` reads a topic; `ha_signed` subscribes to one signed entity over the HA WebSocket; `homewizard_local` polls a HomeWizard P1's own local API, bypassing Home Assistant |
 | `meter_phases` | 1 | 1 or 3. Must match the telegram, or every telegram is rejected and logged |
 | `meter_max_age_s` | 30 | Beyond this the reading is stale and grid power reads as *missing*. On its own it does **not** command 0 W — see the timing note below. It is also the longest a reading is held forward into the 15-minute average |
+| `meter_poll_s` | 5 | `homewizard_local` only. Seconds between polls. **Must be well under `meter_max_age_s`** — see below |
+| `p1_host` | | `homewizard_local` only. The meter's own address, `host` or `host:port` (e.g. `192.168.2.250`) |
 | `meter_mqtt_topic` | | `mqtt_p1` only |
 | `p1_import_entity` | | The **unsigned** consumption sensor. Do not point this at a signed template |
 | `p1_export_entity` | | The **unsigned** injection sensor |
 | `p1_phase_import_entities` | `[]` | L1..L3, in order. Needed for the capacity-tariff peak on a three-phase connection |
 | `p1_phase_export_entities` | `[]` | L1..L3, in order |
+| `p1_net_entity` | | `ha_signed` only. The **signed** net-power sensor: `+` import, `-` export |
+| `p1_phase_net_entities` | `[]` | `ha_signed` only. L1..L3, in order, each signed the same way. Needed for the capacity-tariff peak on a three-phase connection. **The list length must equal `meter_phases`** |
+
+Both per-phase lists are checked against `meter_phases` **once at startup**: a
+list of the wrong length disables P1 ingestion with an error in the log, rather
+than letting every telegram fail its phase-count check one at a time. Leaving
+the list empty is fine and is not an error — you simply get no per-phase
+figures, and therefore no capacity-tariff peak. On a three-phase connection
+that is a much bigger omission than it looks: on a surveyed reading here the
+phases carried 2769 W of import while the connection netted 187 W, so the
+billed quantity is understated roughly fifteenfold if the phases are missing.
 
 #### How long a dead meter takes to reach 0 W
 
@@ -106,6 +155,55 @@ tested, and guessing a key here means guessing a kilowatt:
 it is present it is used for the age, which is what stops a retained message
 replayed on reconnect from presenting a ten-minute-old reading as current.
 
+#### `homewizard_local` — polling the meter instead of Home Assistant
+
+Set `p1_host` to the meter's address and the add-on does `GET /api/v1/data` on
+it every `meter_poll_s` seconds, reading `active_power_w` (signed, same
+convention as `ha_signed`) and the three `active_power_l{1,2,3}_w` fields. Home
+Assistant is not involved: no entity, no WebSocket, no integration to
+mis-configure. Per-phase figures are used only when the meter serves all
+`meter_phases` of them — a single-phase meter returns `null` for L2/L3, and the
+connection-level reading is still accepted on its own.
+
+**Why this mode exists:** every HTTP response is an *arrival*. The meter
+answered, now, with its current reading — whether or not the number moved. That
+is the signal `sensor.p1_sample_age_s` needs and the one Home Assistant cannot
+give it at all (see the note below). It is also simply fewer moving parts: the
+five-second cadence is the meter's own, rather than an integration's polling of
+it re-published as a state change.
+
+**Cadence.** The age is never fresher than the poll interval, so:
+
+| | |
+|---|---|
+| meter's own update rate | ~5.0 s (measured 4.97 s) |
+| `meter_poll_s` default | 5 s — nothing to gain below the meter's own rate |
+| `meter_max_age_s` default | 30 s, i.e. six polls of headroom |
+| `meter_poll_s >= meter_max_age_s` | **refused at startup** — every reading would be stale before its successor arrived |
+| `meter_poll_s > meter_max_age_s / 2` | warned — one missed poll makes the reading stale |
+
+A failed poll — timeout, connection refused, non-200, unparseable body — is a
+**missing** reading. It submits nothing, so the reading does not become 0 W, the
+last good value and its timestamp are left alone, and the age goes on climbing.
+That is exactly what a dead meter should look like.
+
+**What it still cannot see: a frozen meter.** A meter that answers `200 OK`
+forever with a stale number is arriving, so no arrival detector — this one
+included — can tell it from a healthy one. The local API does expose the raw
+material the HA path never had (the `total_power_*_kwh` registers stop
+advancing), and the transport tracks it as `unchanged_s`, but it is deliberately
+*not* folded into the age and *not* thresholded: this controller regulates grid
+power toward ~0 W, and at a converged −10 W the export register needs six
+minutes to move by its 1 Wh resolution while the power figure legitimately
+repeats. Thresholding that at 30 s would rebuild the false-trip limit cycle at
+the exact operating point the controller aims for. Freeze detection is a
+separate problem and needs the low-power case solved first.
+
+You read it yourself instead: the add-on's status page shows it on the P1 line,
+as `… 4 rejected, measurement unchanged for 312 s`. On a house drawing real
+power that figure stays in the seconds; minutes of it while the load is clearly
+not near zero is the meter to go and look at.
+
 #### `sensor.p1_sample_age_s`
 
 Published over MQTT discovery whenever a broker is available: **seconds since the
@@ -123,13 +221,48 @@ The entity is only created when `meter_source` is not `off`. With P1 ingestion
 disabled there is nothing feeding it, and an age sensor climbing with no ingester
 behind it would trip the firmware watchdog on a system that is working fine.
 
-> **Known limit, `mqtt_p1` only.** The age measures *arrival*, not change. On the
-> `ha_dsmr` path that is exactly right: a frozen meter emits no `state_changed`,
-> so nothing arrives and the age climbs. On the MQTT path a bridge that is stuck
-> republishing its last telegram keeps arriving, so the age stays near zero and a
-> frozen meter still looks fresh. Detecting *that* needs a change-detector rather
-> than an arrival-detector, and it is not in this version. Prefer `ha_dsmr` where
-> both are available.
+> **Known limit, `mqtt_p1`.** The age measures *arrival*. On the MQTT path a
+> bridge that is stuck republishing its last telegram keeps arriving, so the age
+> stays near zero and a frozen meter still looks fresh. Detecting *that* needs a
+> change-detector rather than an arrival-detector, and it is not in this version.
+
+> ⚠️ **Known limit, `ha_signed` — do not drive a watchdog off this age yet.**
+> On the HA WebSocket paths the age is stamped when a `state_changed` arrives,
+> which means it measures *time since the value last changed*, not time since
+> the meter last reported. Home Assistant offers nothing better: a repeated
+> reading produces no `state_changed`, does **not** advance `last_reported` on
+> either the REST or the WebSocket serialiser, and `state_reported` cannot be
+> subscribed to over the WebSocket at all (`Event filter is required for event
+> state_reported`). All three measured on the ENV-01 rig against the real
+> HomeWizard integration with the meter frozen: 0 `state_changed` in 70 s and no
+> timestamp movement anywhere.
+>
+> `ha_dsmr` mostly escapes this because a DSMR telegram updates several entities
+> and something in the set almost always moves. **`ha_signed` has exactly one
+> entity, so a healthy meter under a flat load is indistinguishable from a dead
+> one.** This is not hypothetical: in our own captures
+> (`sim/scenarios/ha-p1_meter_active_power-2026-08-20.json`) the real house meter
+> went **42.2 s and 97.0 s** between changes, and 23 Aug peaks at 29.1 s — all
+> past the default `meter_max_age_s` of 30.
+>
+> So `sensor.p1_sample_age_s` on `ha_signed` is safe to *read*, and it is
+> correct whenever the value is moving, but it must not yet be thresholded by
+> the ESP32 stale-input watchdog: a quiet house would trip the battery to 0 W.
+> Raising `meter_max_age_s` is **not** the fix — the two conditions produce an
+> identical signal, so a bigger number only chooses which of the two errors you
+> get. The real fix is an arrival stamp the meter itself provides — and that now
+> exists: **`meter_source: homewizard_local`**. If you have a HomeWizard P1,
+> switch to it. If your meter is only reachable through Home Assistant, this
+> limit still applies to you and the watchdog threshold still must not be armed.
+
+**Where the age is trustworthy:**
+
+| mode | the age measures | safe to threshold from firmware |
+|---|---|---|
+| `homewizard_local` | time since the meter **answered** | **yes** — every HTTP response is an arrival |
+| `ha_dsmr` | time since one of several entities changed | no — statistically usually fine, which is a masked bug, not an absent one |
+| `ha_signed` | time since the one entity changed | **no** — see above |
+| `mqtt_p1` | time since a message arrived | arrivals yes, but a stuck bridge republishing keeps arriving |
 
 ### Control
 
@@ -142,11 +275,60 @@ behind it would trip the firmware watchdog on a system that is working fine.
 | `target_grid_w` | -10 | What the meter should rest at. Negative = a slight export |
 | `step_w` | 10 | Quantisation |
 | `saturation_w` | 500 | Divergence that counts as "the inverter is at a limit" |
-| `saturation_cycles` | 3 | How many consecutive cycles before freezing. A cycle is one *changed* meter reading, not a fixed period - see the note below. **Do not set to 1** |
+| `saturation_cycles` | 3 | How many consecutive cycles before freezing. A cycle is one meter update or `cycle_floor_s`, whichever comes first - see the note below. **Do not set to 1** |
 | `integrator_max_w` | 0 | Bound on the loop's accumulator, and 0 means "same as `max_w`". Caps how much stale error can be waiting to unwind when the sign flips. **Do not raise it above `max_w`** - the output clamp already bounds what is commanded, so the only thing extra headroom buys is more cycles of wrong-direction power after every saturation event. Lowering it below `max_w` is the useful direction |
 | `heartbeat_s` | 10 | Refresh interval; must stay well under the firmware watchdog |
+| `cycle_floor_s` | 15 | The longest the loop may go without evaluating. A deadline on the gap between cycles, reset by every cycle — on a healthy meter it never elapses and changes nothing. Raise it only if your meter is slower than ~10 s; it must stay under `meter_max_age_s`, past which there is no reading to evaluate anyway |
 | `stale_input_s` | 15 | How long inputs may be missing before commanding 0 W. In P1 mode this clock starts only *after* `meter_max_age_s` has already expired — the two stack, see "How long a dead meter takes to reach 0 W" |
 | `auto_start` | false | Start controlling on boot (only after commissioning) |
+| `sign_disagree_w` | 300 | Both the command and the meter must exceed this before a sign difference counts. Must stay **below `max_w`** or the watchdog can never fire, and the add-on refuses to start |
+| `sign_disagree_s` | 180 | How long they must stay opposed, continuously, before the failsafe trips |
+
+#### The sign-disagreement failsafe
+
+If the setpoint this add-on is emitting and the grid figure it is regulating on
+point **opposite ways** — charging the battery while the house imports, or
+discharging it while the house exports — with both over `sign_disagree_w`, for
+`sign_disagree_s` **continuously**, the add-on commands **0 W** and holds it
+there. The banner reads `FAILSAFE`, the commissioning list says which two
+numbers disagreed and for how long, and the `Controller status` entity reports
+`failsafe`.
+
+**It does not clear itself.** Pressing *Start / stop control* twice clears it.
+That is deliberate: commanding 0 W removes the command side of the comparison,
+so the disagreement always vanishes the instant the trip works, and a watchdog
+that took that as proof the fault was over would hand the inverter straight back
+to the loop that was driving the wrong way.
+
+**What it is for.** This is a loop-integrity check: it asks whether the loop's
+output direction still matches the input state it was regulating. It catches a
+polarity error anywhere between the meter and the wire, and an integrator so far
+wound up that unwinding takes minutes. It is the check that would have caught all
+four episodes of 2026-08-20, when a commercial controller charged the battery out
+of the grid, four times, for up to 77 minutes at a time.
+
+**What it is not for.** It does not detect an inverter that acts opposite to what
+it was told — that moves the meter *further* the same way, so command and meter
+agree while everything runs away. That is the saturation freeze's job
+(`saturation_w` / `saturation_cycles`), which compares the command against the
+battery's actual power. The two checks are complementary and neither replaces the
+other.
+
+**Why it will not false-trip on ordinary operation.** A battery that refuses a
+command (empty, full, standby) leaves the meter where it was, so command and
+meter agree. A frozen meter drives the loop into agreeing with it. Around the
+resting point both signals are inside the 300 W gate, so the deadband can never
+produce one. A load step does flip the meter's sign before the loop catches up —
+measured on a full captured day, the longest such crossing is 30 s, against a
+180 s window. And the watchdog is **disarmed whenever the grid-following loop is
+not what is driving**: a maintenance grid charge opposes the meter by design and
+must not be mistaken for a fault.
+
+Both numbers are measured rather than chosen, and are exposed only because the
+ticket requires defaults rather than constants. On the captured healthy day sign
+agreement is 92.9 %; on the four captured fault episodes it is 0.3 %, 0.9 %,
+10.5 % and 0.0 %. There is no reason to move either value without a capture that
+says so.
 
 #### Saturation is counted in cycles, not seconds
 
@@ -154,22 +336,43 @@ The specification states the saturation window as **"> 10 s"**. This add-on coun
 **cycles** instead, and that is a deliberate, accepted deviation rather than an
 oversight - the acceptance criterion is not met as literally written.
 
-A cycle here is one *changed* meter reading: the controller only runs the loop when the
-meter value differs from the previous poll. At the reference P1's ~5 s update rate the
-default of 3 cycles is usually around 15 s, but there is **no guaranteed wall-clock
-window** - a meter that repeats the same value stalls the counter for as long as it
-repeats.
+A cycle here is one meter update **or `cycle_floor_s` elapsing, whichever comes
+first**. At the reference P1's ~5 s update rate the default of 3 cycles is usually
+around 15 s, and the worst case is bounded at `3 x cycle_floor_s` = 45 s. It is still
+not the 10 s the specification asks for, so the deviation stands - but it is now a
+bounded number rather than an open one.
 
-Two reasons that is acceptable:
+⚠️ **This passage used to say something different, and the second half of it was
+wrong.** Until SAFETY-12 the loop ran only when the meter value *changed*, so a meter
+that repeated a value stalled the counter for as long as it repeated, with no upper
+bound at all. That was defended here on the grounds that "a stalled counter is a
+detection-latency limit and not a runaway risk - the condition that stalls it stops the
+whole loop, so nothing accumulates while it is stalled". That argument covers
+**integrator windup and nothing else**. The hazard it misses is **staleness**: while the
+loop was stopped the heartbeat kept re-emitting the last command and the firmware kept
+putting it on the wire every 2 s, so a command computed from an old reading went on
+being executed through a real load change, with every indicator reading healthy.
+Measured on the rig during TEL-05: 70 s at a literally constant 350.0 W, 14 arrivals,
+zero control cycles.
 
-- the control law is a pure function with no clock, which is what makes it testable
-  without hardware, and a seconds-based window would have to live in the controller;
-- a stalled counter is a detection-latency limit and not a runaway risk. The condition
-  that stalls it - an unchanging meter - stops the whole loop, so nothing accumulates
-  while it is stalled.
+The half that survives is the first one: the control law is still a pure function with
+no clock, and the wall-clock window still lives in `Controller`, which has one - see
+`run_control()`. What changed is that the controller now enforces a floor on the gap
+between cycles, so `saturation_cycles` finally means a bounded number of seconds.
 
-If a guaranteed window matters on your site, raise `saturation_cycles` for a fast meter,
-and treat the figure as "N meter updates" rather than "N seconds".
+If a tighter window matters on your site, lower `cycle_floor_s` (not below your meter's
+update interval, or the floor starts firing on a healthy meter) or raise
+`saturation_cycles` for a fast meter.
+
+**This is not a freeze detector, and it deliberately cannot be one.** Nothing here
+decides whether a repeated reading is true — see `unchanged_s` in the meter section for
+why no threshold on that is safe at the converged operating point. The floor only stops
+"the number is the same" from meaning "do not think". The consequence is worth stating
+plainly: against a meter that is genuinely frozen at a wrong value, the loop will now
+correct toward that wrong value instead of holding a stale command. It is bounded by
+`max_w`, the arbiter and the device rating, and it is the same thing that already
+happened to a lying meter whose value merely jittered — bit-exact repetition was never a
+safety property.
 
 #### Why `target_grid_w` is not zero
 

goodwe_controller/app/control.py

@@ -95,19 +95,23 @@ def compute(
     # lets slew be larger than saturation_w.
     #
     # The spec states this window twice and differently: "> 10 s" (§11.2) and
-    # "3 samples" (§10.3). This counts CYCLES, and a cycle is not a unit of
-    # time: run_control() calls cycle() only when the meter value CHANGES
-    # (`if self.grid != last_grid`), so three cycles is three distinct meter
-    # readings and nothing more. At the reference P1's ~5 s update rate that is
-    # usually ~15 s, but there is no upper bound on it - a meter that repeats a
-    # value stalls the counter.
+    # "3 samples" (§10.3). This counts CYCLES, and a cycle is still not a unit
+    # of time - but it is now a BOUNDED one. run_control() runs a cycle on a
+    # changed meter value OR on `cycle_floor_s` elapsing, whichever comes first
+    # (SAFETY-12), so three cycles is at most 3 x cycle_floor_s = 45 s at the
+    # defaults, and usually ~15 s at the reference P1's ~5 s update rate.
     #
-    # That is a detection-latency limit, not a windup hazard: the same
-    # condition that stalls the counter stalls the whole loop, so nothing
-    # accumulates in the meantime either. If a wall-clock window is ever
-    # required, it belongs in Controller (which has a clock) and not here.
-    # ponytail: this function is worth keeping clockless; the ceiling is that
-    # saturation_cycles cannot express a guaranteed number of seconds.
+    # ⚠️ THIS COMMENT USED TO CLAIM there was no upper bound and that it did not
+    # matter, "because the same condition that stalls the counter stalls the
+    # whole loop, so nothing accumulates in the meantime". The first clause was
+    # true and the second was the bug: a stalled loop does not stop commanding,
+    # it goes on emitting its last command through the heartbeat. Windup was
+    # never the hazard; staleness was.
+    #
+    # The wall-clock window lives in Controller, which has a clock, exactly as
+    # this comment always said it should. ponytail: this function stays
+    # clockless; the remaining ceiling is that saturation_cycles expresses a
+    # bound in seconds rather than an exact number of them.
     saturated_now = abs(prev_w - actual_w) > tuning.saturation_w
     sat_count = min(sat_count + 1, 10) if saturated_now else 0
     frozen = sat_count >= tuning.saturation_cycles

goodwe_controller/app/main.py

@@ -40,6 +40,8 @@ from .hass import HomeAssistant
 from .maintenance import IDLE, MaintConfig, Maintenance
 from .mqtt import MqttPublisher
 from .p1 import P1Ingest, build_source, is_enabled
+from .validate import ConfigRefused, refuse, validate_startup_config
+from .watchdog import SignWatchdog, SignWatchdogConfig
 from . import web
 
 OPTIONS_PATH = "/data/options.json"
@@ -56,11 +58,22 @@ def load_options() -> dict:
 
 
 class Controller:
-    def __init__(self, opts: dict, hass: HomeAssistant, store, mqtt_pub):
+    def __init__(self, opts: dict, hass: HomeAssistant, store, mqtt_pub, *, stop):
         self.o = opts
         self.hass = hass
         self.store = store
         self.mqtt = mqtt_pub
+        # ⚠️ REQUIRED, AND KEYWORD-ONLY, AFTER A REVIEW CATCH. This started life
+        # as `stop=None`, which made a Controller that CANNOT STOP ITSELF the
+        # default one. On the late-refusal path in run_control() that default
+        # meant: log the banner, return, and leave the process alive forever
+        # with no control loop, no exit and no further output - the exact
+        # "inert but looks healthy" failure this whole module exists to refuse.
+        # amain() always passed a real Event, so it was latent, but test_p1.py
+        # was already constructing Controllers without one. No default now, so
+        # the broken shape does not typecheck.
+        self.stop_event = stop
+        self.refused: list[str] | None = None
 
         self.tuning = Tuning(
             gain=float(opts.get("gain", 0.6)),
@@ -91,12 +104,22 @@ class Controller:
             store,
         )
 
+        # SAFETY-02. One instance, one actuator, one cadence - see watchdog.py.
+        self.sign_wd = SignWatchdog(SignWatchdogConfig(
+            min_w=float(opts.get("sign_disagree_w", 300)),
+            hold_s=float(opts.get("sign_disagree_s", 180)),
+        ))
+
         # P1 ingestion (TEL-01). `meter_source: off` keeps the original
         # single-entity meter_entity path, so an existing install is unchanged
         # until it opts in.
         self.p1 = P1Ingest(phases=int(opts.get("meter_phases", 1)),
                            max_age_s=float(opts.get("meter_max_age_s", 30)))
         self.p1_enabled = is_enabled(opts)
+        # Set by amain() once the transport is built, so the status page can show
+        # what only the transport knows (homewizard_local's unchanged_s). Stays
+        # None when P1 is off, or under a transport that has no such counter.
+        self.p1_source = None
 
         # live state
         self.auto = bool(store.data.get("auto", opts.get("auto_start", False)))
@@ -104,6 +127,11 @@ class Controller:
         self.sat_count = 0
         self.i_w = 0.0        # the loop's integrator, carried between cycles
         self.loop_w = None    # what the loop asked for last cycle, or None
+        # Did the grid-following loop actually win the LAST arbitration? That is
+        # the question SAFETY-02 has to ask about the command standing on the
+        # wire right now, so it is recorded when the arbitration happens rather
+        # than re-derived a cycle later. Starts False: nothing is on the wire.
+        self.following = False
         self.reason = "starting"
         self.grid = self.soc = self.batt = None
         self.peak_fc = None
@@ -198,8 +226,29 @@ class Controller:
         for msg in result.events:
             self.log_event(msg)
 
+        # --- SAFETY-02, and it runs BEFORE the early return below -------------
+        # ⚠️ ORDER MATTERS HERE. If this were evaluated after the "inputs missing
+        # but not yet stale" hold, a run of held cycles would leave
+        # `disagree_since` untouched across the gap and the timer would resume
+        # from a start time that predates it. It is evaluated every cycle,
+        # unconditionally, so a missing meter CLEARS the window - see watchdog.py.
+        #
+        # The value compared is the command STANDING ON THE WIRE, which is what
+        # this cycle's fresh meter reading is a response to. `last_write` is that
+        # value after the device clamp and confirmed accepted; `target` covers
+        # the case where nothing has been written yet (and, deliberately, the
+        # case where the last write was REJECTED - the inverter is then still
+        # latched on `last_write`, which is exactly what `last_write` holds).
+        was_tripped = self.sign_wd.tripped
+        standing = self.last_write if self.last_write is not None else self.target
+        if self.sign_wd.evaluate(standing, self.grid, self.following, now) \
+                and not was_tripped:
+            self.log_event("FAILSAFE " + self.sign_wd.reason)
+            _LOG.error("SAFETY-02 TRIPPED - %s. Commanding 0 W and holding it "
+                       "until control is started again.", self.sign_wd.reason)
+
         stale_after = float(self.o.get("stale_input_s", 15))
-        if not self.inputs_ok:
+        if not self.inputs_ok and not self.sign_wd.tripped:
             bad_for = (now - self.inputs_bad_since).total_seconds() if self.inputs_bad_since else 0.0
             if bad_for < stale_after:
                 # A single missed poll is not a fault. Hold, keep the heartbeat
@@ -219,6 +268,16 @@ class Controller:
         claims.append(Claim.limit("supervised", P_SAFETY, -max_w, max_w, "max_w"))
 
         # --- safety stops ----------------------------------------------------
+        # ⚠️ SAFETY-02 is claimed FIRST and unconditionally while latched. It is
+        # a SET at P_SAFETY, so it outranks maintenance, peak shaving and the
+        # loop alike - a controller pushing power the wrong way is wrong
+        # whatever it thinks it is doing. Re-filed EVERY cycle: claims are not
+        # sticky, and one filed once would lapse the next cycle and hand the
+        # actuator silently back to the loop that was driving the wrong way.
+        if self.sign_wd.tripped:
+            claims.append(Claim.set("failsafe", P_SAFETY, 0.0,
+                                    "sign disagreement"))
+
         if not self.auto:
             claims.append(Claim.set("safety", P_SAFETY, 0.0, "stopped"))
         elif not self.inputs_ok:
@@ -290,6 +349,28 @@ class Controller:
         resolution = resolve(claims)
         if resolution.contradiction:
             self.log_event("ARBITER CONTRADICTION - commanding 0 W, see the log")
+        # --- SAFETY-02's arming gate ------------------------------------------
+        # Was the number about to go on the wire chosen by the grid-following
+        # loop, or by a strategy that commands against the meter on purpose?
+        # Only the former is expected to agree in sign with P1. See gate 1 in
+        # watchdog.py - without this, every maintenance grid charge trips the
+        # failsafe within three minutes of starting.
+        #
+        # ⚠️ "THE LOOP WON" IS NOT ENOUGH, and the difference is a whole class of
+        # false trip. A LIMIT claim can survive the loop winning and still
+        # replace its number: maintenance's charge-only shaping is
+        # `hi = -charge_w`, so the loop can ask for +500 W of discharge, win the
+        # arbitration, and have the emitted value come out at -2500 W of grid
+        # charge. Winner says "loop"; the wire carries maintenance's intent. So
+        # the test is on the NUMBER, not on the name: the loop is following only
+        # while the emitted value points the way the loop asked and is no larger
+        # than it asked - i.e. limits reduced it, they did not redirect it.
+        # Zero on either side falls out as not-following, which costs nothing:
+        # a 0 W command cannot be a wrong-direction command.
+        asked = self.loop_w
+        self.following = (resolution.winner == "loop" and asked is not None
+                          and resolution.target_w * asked > 0
+                          and abs(resolution.target_w) <= abs(asked))
         self.target = resolution.target_w
         self.reason = resolution.explain()
         await self.write_setpoint(self.target)
@@ -299,19 +380,112 @@ class Controller:
         entity = self.o.get("setpoint_entity", "")
         if entity:
             self.dev_min, self.dev_max, _ = await self.hass.limits(entity)
-            if self.dev_max is not None and self.tuning.max_w > self.dev_max:
-                self.log_event(
-                    f"clamp {self.tuning.max_w:.0f} W exceeds the device maximum "
-                    f"{self.dev_max:.0f} W - the device wins")
+            # ⚠️ THIS USED TO WARN AND CARRY ON, and that was the bug CFG-01
+            # exists to remove: a max_w above the device's rating meant
+            # write_setpoint() silently clamped and the configured ceiling was
+            # never the real one.
+            #
+            # amain() already ran this gate before anything started. It runs
+            # AGAIN here for one case the gate cannot cover: ESPHome is often
+            # not up yet when the add-on boots, so hass.limits() returned
+            # (None, None) and the range checks were skipped rather than
+            # guessed at. This is the first moment the device's real rating is
+            # known. If it conflicts, refuse now - stopping deterministically
+            # through the normal shutdown, which commands 0 W on the way out.
+            problems = validate_startup_config(self.o, self.dev_min, self.dev_max)
+            if problems:
+                refuse(problems)
+                self.refused = problems
+                self.log_event("REFUSED: " + problems[0])
+                # Signal, then return WITHOUT entering the loop. amain() wakes
+                # on this, runs the normal wind-down (which commands 0 W) and
+                # re-raises ConfigRefused afterwards, so the exit code is 78 and
+                # the inverter is left at zero rather than latched.
+                self.stop_event.set()
+                return
 
         last_grid = object()
         heartbeat = float(self.o.get("heartbeat_s", 10))
         last_beat = 0.0
+        # ⚠️ SAFETY-12. The floor is a DEADLINE ON THE GAP BETWEEN CYCLES, not a
+        # second scheduler running alongside the arrival trigger. Every cycle
+        # resets it, whichever trigger fired, so on a healthy changing meter it
+        # never elapses and not one existing cycle moves - and therefore no
+        # change to the per-cycle gain the tuning was measured against.
+        #
+        # That is true twice over, and the second reason is the sturdier one:
+        # the combined cycle rate is max(arrival rate, 1/floor), never the sum.
+        # At the defaults 1/15 s is strictly slower than the ~1/5 s arrival
+        # rate, so even a floor that raced the arrivals could not push the loop
+        # past its nominal healthy rate. The re-tune is unreachable by
+        # construction, not merely by the reset. ⚠️ That argument holds only
+        # while floor > the meter's update interval - which is why the schema
+        # minimum of 5 s deserves the second look validate.py has not given it
+        # yet: 5 s IS the reference meter's interval, i.e. the one configurable
+        # value that would double the cycle rate.
+        #
+        # Why it has to exist, and it is not only about latency: `self.grid !=
+        # last_grid` alone means a meter that repeats a value runs NO control
+        # cycles at all. The heartbeat below keeps re-emitting the last command
+        # and the firmware keeps putting it on the wire, so every indicator
+        # reads healthy - and, worse, the `inputs missing -> 0 W` claim lives
+        # INSIDE cycle(), so on a repeating meter THAT SAFETY CLAIM CANNOT FIRE.
+        # Demonstrated in test_loop.py: constant meter, SoC entity dies at t=4 s,
+        # and the pre-fix controller holds 220 W through the whole outage with
+        # the status line still reading "loop -> 220 W". Layer 1 does not cover
+        # it on a `meter_source: off` install either - no P1 age sensor is
+        # published, so the firmware has nothing to veto on. Measured on the rig
+        # during TEL-05: 70 s at a literally constant 350.0 W, 14 arrivals, zero
+        # cycles.
+        #
+        # This is NOT a freeze detector, and deliberately so - see
+        # HomeWizardLocalSource.unchanged_s for why one cannot be built here (at
+        # the converged -10 W target a 1 Wh register needs ~6 minutes to move,
+        # so any freeze threshold false-trips at the exact operating point we
+        # run at). Nothing here decides whether a repeated reading is true. It
+        # only stops "the number is the same" from meaning "do not think".
+        #
+        # ⚠️ THE 15 s DEFAULT HAS A CEILING IT DOES NOT OWN. It is under
+        # validate.FIRMWARE_INGEST_VETO_S (30 s) and under meter_max_age_s on
+        # purpose, so the loop re-decides at least twice inside any window in
+        # which layer 1 might otherwise be the only thing deciding. If the
+        # firmware's veto ever moves, this default moves with it - it is not
+        # independently justified at 15.
+        floor = float(self.o.get("cycle_floor_s", 15))
+        last_cycle = None
         while not self.stopping:
             await self.read_inputs()
-            # A cycle is one meter update, exactly as on the reference install.
-            if self.grid != last_grid:
+            now_mono = asyncio.get_running_loop().time()
+            # A cycle is one meter update, exactly as on the reference install -
+            # or the floor elapsing, whichever comes first.
+            overdue = last_cycle is None or (now_mono - last_cycle) >= floor
+            if self.grid != last_grid or overdue:
                 last_grid = self.grid
+                last_cycle = now_mono
+                # ⚠️ The FULL cycle, not a degraded one. A floor cycle runs the
+                # same law on the same inputs as an arrival cycle, because in P1
+                # mode the freshness question is already answered upstream and
+                # answered harder: past `meter_max_age_s` (30 s) p1.net_w is
+                # None, which is "inputs missing", which becomes a P_SAFETY 0 W
+                # claim. So a floor cycle cannot run the PI on a 60 s old
+                # figure, because at 60 s there is no figure.
+                #
+                # ⚠️ THAT GUARANTEE IS TRANSPORT-CONDITIONAL, and saying so
+                # matters more than the guarantee: with `meter_source: off`,
+                # read_inputs() takes self.grid straight from hass.number() with
+                # NO age gate at all, so a Home Assistant entity that has gone
+                # quiet reads as a current value on that path with or without
+                # this change. Running the full law is still the right choice
+                # there - the alternative is a degraded second law reasoning
+                # about an age nobody measured - but the floor does not make
+                # that path fresh, and nothing here should be read as claiming
+                # it does. And the integrator
+                # advances per CYCLE, not per second (control.py), so bounding
+                # the gap bounds the accumulation: at most one extra
+                # gain x error per floor interval, under the same
+                # integrator_max_w as every other cycle. A second, gentler
+                # control law for floor cycles would be a second set of
+                # dynamics nobody can test on this hardware.
                 await self.cycle()
             # ⚠️ The heartbeat is not an optimisation. The ESP32 treats silence
             # longer than ~30 s as "the controller is gone" and zeroes the
@@ -330,10 +504,18 @@ class Controller:
             "battery": self.batt,
             "soc": self.soc,
             "phase": self.maint.phase,
-            "status": "running" if self.auto else "stopped",
+            # ⚠️ SAFETY-02's alarm surface, and it is deliberately an existing
+            # one. IF-01/IF-02 own `ems/event/failsafe` and the `failsafe active`
+            # binary sensor and neither is built yet; inventing a bespoke topic
+            # here would be a surface to migrate later. This sensor is already
+            # discovered, already on every dashboard, and "failsafe" is
+            # additive to its vocabulary rather than a change to it.
+            "status": ("failsafe" if self.sign_wd.tripped
+                       else "running" if self.auto else "stopped"),
         }
         # ⚠️ ONLY when P1 ingestion is actually running. The ESP32's stale-input
-        # watchdog subscribes to sensor.p1_sample_age_s and forces the layer-1
+        # watchdog subscribes to sensor.goodwe_p1_sample_age - see the entity-id
+        # note in mqtt.py; the composed name is not the object_id - and forces layer-1
         # failsafe once it reaches max_age_s. With meter_source off there is no
         # ingester feeding it, so published_age_s would be time-since-startup
         # climbing without bound - i.e. every existing install would cross the
@@ -365,10 +547,22 @@ class Controller:
                                     + (f" - last error: {self.p1.last_error}"
                                        if self.p1.last_error else "")})
             else:
+                # ⚠️ unchanged_s is REPORTED, never thresholded and never folded
+                # into the age - see HomeWizardLocalSource.unchanged_s for why
+                # (at the converged -10 W this controller aims for, a 1 Wh
+                # register needs ~6 minutes to move, so any limit false-trips at
+                # the exact operating point we target). The whole argument for
+                # leaving it unthresholded is that a human interprets it, which
+                # requires a human being able to see it - so here it is. getattr:
+                # only homewizard_local has one, and p1_source is None until
+                # amain() builds the transport.
+                unchanged = getattr(self.p1_source, "unchanged_s", None)
                 out.append({"ok": True, "warn": False,
                             "text": f"P1 meter ({o.get('meter_source')}): {self.p1.net_w:g} W, "
                                     f"{age:.0f} s old, {self.p1.samples} telegrams, "
-                                    f"{self.p1.parse_errors} rejected"})
+                                    f"{self.p1.parse_errors} rejected"
+                                    + (f", measurement unchanged for {unchanged:.0f} s"
+                                       if unchanged is not None else "")})
         rows = [("battery SoC", self.soc, o.get("soc_entity")),
                 ("battery power", self.batt, o.get("batt_entity"))]
         if not self.p1_enabled:
@@ -399,6 +593,22 @@ class Controller:
             out.append({"ok": False, "warn": False,
                         "text": "last write to the inverter was REJECTED - check the log"})
 
+        # SAFETY-02. Reported in both states: a watchdog nobody can see is armed
+        # is a watchdog nobody trusts when it fires.
+        if self.sign_wd.tripped:
+            out.append({"ok": False, "warn": False,
+                        "text": "SIGN-DISAGREEMENT FAILSAFE - " + self.sign_wd.reason
+                                + ". The inverter is held at 0 W. Find out why the "
+                                  "command opposed the meter before starting control "
+                                  "again; starting clears this."})
+        else:
+            held = self.sign_wd.held_s
+            out.append({"ok": True, "warn": False,
+                        "text": f"sign watchdog: armed (trips after "
+                                f"{self.sign_wd.cfg.hold_s:.0f} s opposed, both over "
+                                f"{self.sign_wd.cfg.min_w:.0f} W)"
+                                + (f" - opposed for {held:.0f} s now" if held else "")})
+
         if not o.get("estop_fitted", False):
             out.append({"ok": False, "warn": True,
                         "text": "no e-stop fitted: if this host dies the battery stays "
@@ -416,7 +626,11 @@ class Controller:
     def status_payload(self) -> dict:
         checks = self.checks()
         bad = [c for c in checks if not c["ok"] and not c["warn"]]
-        if bad:
+        if self.sign_wd.tripped:
+            # Outranks "NOT READY": nothing is missing, something went wrong.
+            level, banner = "bad", ("FAILSAFE — the command opposed the meter. "
+                                    "Inverter held at 0 W.")
+        elif bad:
             level, banner = "bad", f"NOT READY — {bad[0]['text']}"
         elif not self.auto:
             level, banner = "warn", "Stopped — inverter commanded to 0 W"
@@ -450,6 +664,15 @@ class Controller:
             self.auto = not self.auto
             self.store.set("auto", self.auto)
             self.log_event("control started" if self.auto else "control stopped")
+            if self.auto and self.sign_wd.tripped:
+                # ⚠️ THE ONLY WAY OUT OF A SIGN-DISAGREEMENT TRIP, on purpose.
+                # It clears on a deliberate human start, not on the condition
+                # going away - the condition ALWAYS goes away, because the trip
+                # commands 0 W and a 0 W command cannot disagree with anything.
+                # An operator pressing start has, at minimum, looked at the
+                # banner that says why.
+                self.sign_wd.reset()
+                self.log_event("sign-disagreement failsafe cleared by operator")
             if not self.auto:
                 self.target = 0.0
                 await self.write_setpoint(0.0, force=True)
@@ -498,6 +721,26 @@ async def amain() -> None:
         except Exception as _e:  # noqa: BLE001
             _LOG.error("core api probe failed: %s", _e)
 
+        # ⚠️ THE STARTUP GATE (CFG-01). Nothing below this line may run on a
+        # configuration validate.py rejects - specs §1.5: a config the system
+        # cannot honour is refused at startup, not survived at runtime.
+        #
+        # It sits HERE, before the broker, before the web server and before any
+        # task exists, so a refusal cannot leave half a controller running with
+        # a UI in front of it. Reading the device range is the one thing the
+        # validator cannot do for itself; (None, None) when ESPHome has not come
+        # up yet is not a refusal - run_control() re-checks once the real rating
+        # is known. See validate.py for where the line is drawn and why.
+        _sp = str(opts.get("setpoint_entity", "") or "").strip()
+        _dev_min = _dev_max = None
+        if _sp:
+            _dev_min, _dev_max, _ = await hass.limits(_sp)
+            _LOG.info("setpoint device %s reports range %s…%s W", _sp, _dev_min, _dev_max)
+        _problems = validate_startup_config(opts, _dev_min, _dev_max)
+        if _problems:
+            refuse(_problems)
+            raise ConfigRefused(_problems)
+
         # ⚠️ Status publishing must NEVER be able to stop the controller. A
         # broken broker, a missing library, an API change in paho - all of it is
         # observability, and the battery does not care. Caught broadly and on
@@ -523,10 +766,10 @@ async def amain() -> None:
 
             pub = _NoMqtt()
 
-        controller = Controller(opts, hass, store, pub)
+        stop = asyncio.Event()
+        controller = Controller(opts, hass, store, pub, stop=stop)
         runner = await web.start(controller, port=8099)
 
-        stop = asyncio.Event()
         loop = asyncio.get_running_loop()
         for sig in (signal.SIGTERM, signal.SIGINT):
             with contextlib.suppress(NotImplementedError):
@@ -540,6 +783,7 @@ async def amain() -> None:
         # unit - would be computed from a fraction of the data.
         p1_source = build_source(opts, controller.p1, session, broker)
         if p1_source is not None:
+            controller.p1_source = p1_source     # so checks() can report on it
             tasks.append(asyncio.create_task(p1_source.run()))
 
         await stop.wait()
@@ -552,6 +796,10 @@ async def amain() -> None:
                 await task
         await runner.cleanup()
         _LOG.info("stopped")
+        # The late-arriving-device refusal from run_control(). Re-raised only
+        # now, so the wind-down above still ran and the inverter is at 0 W.
+        if controller.refused:
+            raise ConfigRefused(controller.refused)
 
 
 def main() -> None:
@@ -559,6 +807,13 @@ def main() -> None:
         asyncio.run(amain())
     except KeyboardInterrupt:
         pass
+    except ConfigRefused:
+        # ⚠️ No traceback, on purpose. The banner refuse() already printed says
+        # everything an operator needs, and a stack trace on top of it would say
+        # "this crashed" - the exact confusion AC3 is about. 78 is sysexits(3)
+        # EX_CONFIG, so even a script reading the exit status can tell a bad
+        # config from a bug.
+        raise SystemExit(78)
 
 
 if __name__ == "__main__":

goodwe_controller/app/mqtt.py

@@ -45,13 +45,32 @@ SENSORS = [
     ("soc", "goodwe_battery_soc", "Battery SoC", "%", "battery", "measurement", None),
     ("phase", "goodwe_maintenance_phase", "Maintenance phase", None, None, None, "mdi:battery-sync"),
     ("status", "goodwe_controller_status", "Controller status", None, None, None, "mdi:heart-pulse"),
-    # ⚠️ This one deliberately breaks the goodwe_ prefix above: the entity id
-    # must be exactly `sensor.p1_sample_age_s`, because SAFETY-01's firmware
-    # watchdog subscribes to that literal id and the ENV-01 simulation rig
-    # asserts on it. Renaming it silently disarms a safety layer. It is seconds
-    # since the newest accepted P1 telegram, republished every second so that a
-    # meter frozen at a constant value still shows a climbing age - which is the
-    # false-trip that this entity exists to remove.
+    # ⚠️ THE LIVE ENTITY IS `sensor.goodwe_p1_sample_age`, NOT what this
+    # object_id spells. An earlier version of this comment said the id "must be
+    # exactly sensor.p1_sample_age_s" - that name has never existed on any HA,
+    # and believing it is how a safety layer gets disarmed by someone tidying up.
+    #
+    # On HA 2026.8 `object_id` in a discovery payload does NOT determine the
+    # entity_id. HA composes it from the device name plus the entity name:
+    # "GoodWe RS485 Controller" + "P1 sample age" -> sensor.goodwe_p1_sample_age.
+    # Verified against the live system 2026-08-26; the firmware subscribes to
+    # that composed name (goodwe-master-stage4-failsafe.yaml, homeassistant
+    # sensor p1_age_s), and its own comment records that sensor.p1_sample_age_s
+    # never existed.
+    #
+    # So: do NOT "fix" the firmware to match the object_id below, and do not
+    # rename the device or this entity's friendly name - either changes the
+    # composed id and silently disarms the ingest guard, because has_state()
+    # simply stays false forever and nothing reports it. The firmware calls this
+    # out as the failure that "FAILS SILENTLY AND LOOKS CORRECT".
+    #
+    # The value: seconds since the newest accepted P1 telegram, republished
+    # every second so a meter frozen at a constant value still shows a climbing
+    # age - the false-trip this entity exists to remove.
+    #
+    # ⚠️ Separately, and not fixed here: the firmware's ingest guard tests this
+    # sensor's VALUE rather than its arrival, so a dead publisher freezes the
+    # number and reads permanently fresh. Filed as TEL-06.
     ("p1_age", "p1_sample_age_s", "P1 sample age", "s", "duration", "measurement", None),
 ]
 

goodwe_controller/app/p1.py

@@ -4,13 +4,22 @@ Everything downstream trusts this module: the safety checks, the capacity-tariff
 peak, the optimizer, the control loop's sign. So three things happen here and
 nowhere else.
 
-  1. The IMPORT/EXPORT DERIVATION. A Belgian P1 meter exposes two UNSIGNED
-     registers - consumption and injection - never one signed figure. Net power
-     is `import_w - export_w`, positive = import, and that subtraction is done
+  1. The IMPORT/EXPORT DERIVATION. A Belgian P1 read over DSMR exposes two
+     UNSIGNED registers - consumption and injection. Net power is
+     `import_w - export_w`, positive = import, and that subtraction is done
      exactly once, here (spec §5.2: "the derivation is the EMS's job, not a
      template the user has to write"). A second copy of it somewhere else is a
      second chance to invert the control loop.
 
+     Some P1 readers - the HomeWizard P1 among them - publish the OTHER shape:
+     one SIGNED figure, positive = import, and no unsigned registers at all.
+     `split_signed()` fans that back out into the same two magnitudes, so there
+     is still exactly one internal representation and one sign convention. ⚠️ It
+     lives here, next to the subtraction, for the same reason the subtraction
+     does: the moment a user is asked to write two template sensors that split a
+     signed value, the sign convention is back in unreviewed YAML underneath a
+     safety input, which is precisely what §5.2 moved into the EMS.
+
   2. THE INGEST TIMESTAMP. Every accepted sample is stamped on arrival. A value
      with no age is a value that cannot be trusted (§5.2), and staleness is the
      failsafe trigger (§11.2).
@@ -47,6 +56,8 @@ _LOG = logging.getLogger("goodwe.p1")
 
 SOURCE_HA = "ha_dsmr"
 SOURCE_MQTT = "mqtt_p1"
+SOURCE_HA_SIGNED = "ha_signed"
+SOURCE_HOMEWIZARD = "homewizard_local"
 
 QUARTER_S = 900
 
@@ -78,7 +89,7 @@ class P1Sample:
     ingest_ts: datetime            # tz-aware UTC, set at ingest
     ingest_mono: float             # time.monotonic() at ingest - see age_s()
     telegram_ts: datetime | None   # from the telegram, where the source has one
-    source: str                    # SOURCE_HA | SOURCE_MQTT
+    source: str                    # one of the SOURCE_* constants above
     import_w: float                # unsigned magnitude, as the meter reports it
     export_w: float                # unsigned magnitude
     net_w: float                   # import_w - export_w  (+ import, - export)
@@ -129,6 +140,29 @@ def _watts(value, what: str) -> float:
     return out
 
 
+def split_signed(net_w) -> tuple[float, float]:
+    """One signed figure -> the (import, export) magnitudes the module speaks.
+
+    The inverse of make_sample's subtraction, and the easy direction: no second
+    register to disagree with, so there is nothing to mix a fresh reading with a
+    stale one. `+` is import, `-` is export - verified in test_p1.py against real
+    captured readings from this house's own meter, not against a datasheet.
+
+    ⚠️ Exactly one of the two comes out non-zero. Splitting into `(max(v,0),
+    max(-v,0))` rather than clamping keeps `import_w - export_w == v` exactly, so
+    the signed value the meter published survives the round trip bit for bit -
+    a control loop must not be steered by a number that changed on the way in.
+
+    ⚠️ Validation is `_watts`, the same gate the unsigned path uses: NaN,
+    infinity, non-numbers and the §20 open-question-5 unsigned-decode
+    contamination (64954 for -582 W) are all refused here rather than believed.
+    A signed source makes that check MORE important, not less - on this path
+    64954 is not obviously wrong the way a negative "unsigned" register is.
+    """
+    v = _watts(net_w, "net")
+    return (v, 0.0) if v >= 0 else (0.0, -v)
+
+
 def make_sample(source: str, import_w, export_w, *, phases: int,
                 phase_import_w=None, phase_export_w=None,
                 telegram_ts: datetime | None = None,
@@ -668,6 +702,333 @@ class MqttP1Source:
             self.ingest.reject(err)
 
 
+# --------------------------------------------------------------------------- #
+# transport 3: Home Assistant WebSocket, one signed entity
+# --------------------------------------------------------------------------- #
+class HaSignedSource(HaDsmrSource):
+    """The same websocket, subscribed to ONE signed power entity.
+
+    For readers that publish net power as a single signed figure - a HomeWizard
+    P1's `sensor.p1_meter_active_power`, positive = import - rather than the two
+    unsigned DSMR registers. This is the meter actually installed at the house,
+    and `ha_dsmr` cannot read it: it needs two registers and refuses a negative
+    one outright, which is every exporting telegram.
+
+    ⚠️ A subclass, not a copy. The connect / auth / subscribe / reconnect /
+    `_absorb` machinery above is transport, not shape, and it has already been
+    debugged once - notably "prime the cache from get_states but never build a
+    sample out of it" and "a reconnect emits nothing". Only `_wanted` (which
+    entity ids) and `build` (how they become a sample) differ, so only those two
+    are overridden. Everything TEL-01 established therefore applies unchanged:
+    ingest timestamping, meter_max_age_s, the clock-recomputed age sensor, and
+    `unavailable` treated as a missing reading rather than 0 W.
+
+    ⚠️ THE AGE ON THIS TRANSPORT MEASURES TIME SINCE THE VALUE CHANGED, not time
+    since the meter reported, and on one entity those are very different things.
+    Home Assistant offers no arrival signal for a repeated reading: it emits no
+    `state_changed`, it does not advance `last_reported` on either serialiser,
+    and `state_reported` cannot be subscribed to over the websocket at all
+    ("Event filter is required for event state_reported"). All three measured on
+    the ENV-01 rig against the real HomeWizard integration with the meter frozen
+    - 0 state_changed in 70 s, no timestamp movement anywhere.
+
+    `ha_dsmr` mostly escapes it because a DSMR telegram moves several entities at
+    once. This transport has ONE, so a healthy meter under a flat load looks
+    exactly like a dead one - and our own capture has the real meter going 42.2 s
+    and 97.0 s between changes, both past the default max_age_s of 30. Hence
+    DOCS.md: sensor.p1_sample_age_s is correct while the value moves and must not
+    yet be thresholded by the firmware watchdog on this transport. Raising
+    meter_max_age_s does not fix it, it only chooses which of the two errors you
+    get. The fix is an arrival stamp from the meter itself - reading the
+    HomeWizard local API rather than an HA entity - which is a separate ticket.
+
+    ⚠️ The debounce is inherited but does nothing useful here, and that is fine:
+    one telegram is one entity, so there is no burst of per-entity events to
+    coalesce and no window in which a new reading sits beside a stale one. It
+    costs one scheduled sleep per telegram at ~0.2 Hz. Left in place rather than
+    special-cased, because a second code path through build() is a second place
+    for the sign to go wrong.
+    """
+
+    def _wanted(self) -> set[str]:
+        out = set()
+        if self.entities.get("net"):
+            out.add(self.entities["net"])
+        out.update(e for e in self.entities.get("phase_net") or [] if e)
+        return out
+
+    def build(self) -> bool:
+        """Assemble one sample from the cache. Returns True if one was accepted."""
+        net_id = self.entities.get("net")
+        if net_id not in self.cache:
+            return False
+        pn = [self.cache.get(e) for e in self.entities.get("phase_net") or []]
+        if pn and None in pn:
+            return False           # incomplete phase set: wait, do not guess
+        try:
+            imp, exp = split_signed(self.cache[net_id])
+            pi = pe = None
+            if pn:
+                # ponytail: this split is arithmetically redundant today -
+                # make_sample subtracts the two lists again and does not
+                # sign-check per-phase figures, so handing it the signed values
+                # with a zero export list produces the identical tuple. Verified:
+                # mutating it that way leaves all 174 checks green, i.e. no test
+                # can tell the difference, and it is recorded here rather than
+                # left as a silent equivalent mutant for the next reviewer to
+                # rediscover. Kept because `phase_import_w` means a MAGNITUDE:
+                # a negative in it is the double-signing that make_sample refuses
+                # outright for the connection-level registers, and the day that
+                # check is extended per-phase the shortcut breaks the meter, not
+                # the test.
+                pairs = [split_signed(v) for v in pn]
+                pi = [a for a, _ in pairs]
+                pe = [b for _, b in pairs]
+            self.ingest.submit(make_sample(
+                SOURCE_HA_SIGNED, imp, exp,
+                phases=self.ingest.phases,
+                phase_import_w=pi, phase_export_w=pe,
+                # ⚠️ No telegram_ts, for the same reason as ha_dsmr: HA's
+                # last_changed is when the VALUE changed, which on a steady meter
+                # is minutes ago while the telegram is current. sensor.
+                # p1_sample_age_s is what covers a genuinely frozen meter.
+            ))
+            return True
+        except P1Error as err:
+            self.ingest.reject(err)
+            return False
+
+
+# --------------------------------------------------------------------------- #
+# transport 4: the HomeWizard P1's own local API
+# --------------------------------------------------------------------------- #
+HOMEWIZARD_PATH = "/api/v1/data"
+HOMEWIZARD_PORT = 80
+
+
+def parse_homewizard(doc, phases: int, *, now: datetime | None = None,
+                     ingest_mono: float | None = None) -> P1Sample:
+    """One `GET /api/v1/data` document -> a sample. Raises P1Error.
+
+    The meter's own JSON, of which we read four keys:
+
+        {"active_power_w": -5710.0,          # SIGNED, + import  - export
+         "active_power_l1_w": ..., "active_power_l2_w": ..., "..._l3_w": ...,
+         "total_power_import_kwh": 1234.567, "total_power_export_kwh": 890.123}
+
+    Same shape as `ha_signed` - one signed connection figure plus signed
+    per-phase figures - so it goes through the same `split_signed` and the same
+    `make_sample`. Nothing about the sign convention is re-derived here.
+
+    ⚠️ No telegram timestamp, because the API carries none, and that is correct
+    rather than a gap: the document was produced by the meter in the moment it
+    answered, so the ingest stamp IS the measurement time. This is the whole
+    reason the transport exists - see HomeWizardLocalSource.
+
+    ⚠️ Per-phase figures are taken only when the meter serves ALL `phases` of
+    them. A single-phase HomeWizard returns `active_power_l2_w: null`, and a
+    partial set must not become a fabricated tuple. Unlike the HA transports
+    there is no "wait for the rest" case to worry about: every field here came
+    out of ONE response, so a missing phase cannot be a stale phase, and the
+    connection-level reading is still a genuine, complete measurement. Dropping
+    the whole sample over an absent per-phase field would turn a healthy meter
+    into a climbing age, which is the exact false-trip this ticket removes.
+    """
+    if not isinstance(doc, dict):
+        raise P1Error(f"meter response is not a JSON object ({type(doc).__name__})")
+
+    imp, exp = split_signed(doc.get("active_power_w"))
+
+    pi = pe = None
+    # ⚠️ range(phases), not the legs the meter served: a 3-phase meter configured
+    # as meter_phases: 1 yields a per-phase tuple covering ONE leg of three.
+    # Control is unaffected (it uses the connection figure), but the
+    # capacity-tariff peak is understated. Filed separately - not fixed here.
+    legs = [doc.get(f"active_power_l{i + 1}_w") for i in range(phases)]
+    if all(v is not None for v in legs):
+        pairs = [split_signed(v) for v in legs]
+        pi = [a for a, _ in pairs]
+        pe = [b for _, b in pairs]
+
+    return make_sample(SOURCE_HOMEWIZARD, imp, exp, phases=phases,
+                       phase_import_w=pi, phase_export_w=pe,
+                       ingest_ts=now, ingest_mono=ingest_mono)
+
+
+def measurement_fingerprint(doc) -> tuple:
+    """The part of a response that a genuinely new measurement has to move.
+
+    Power plus both energy registers. A meter under any real load advances a
+    kWh counter (1 Wh resolution: ~10 s at 350 W), so this changes even when the
+    power figure happens to repeat. Used ONLY for `unchanged_s` - see there for
+    why it must not be allowed anywhere near the age.
+    """
+    if not isinstance(doc, dict):
+        return ()
+    return (doc.get("active_power_w"),
+            doc.get("total_power_import_kwh"),
+            doc.get("total_power_export_kwh"))
+
+
+class HomeWizardLocalSource:
+    """Polls the meter's own local HTTP API instead of a Home Assistant entity.
+
+    ⚠️ THIS IS THE ONLY TRANSPORT WHOSE AGE MEASURES ARRIVAL. That is the entire
+    reason it exists, and it is not an optimisation - it is the difference
+    between an age sensor a firmware watchdog may threshold and one it may not.
+
+    Every HTTP response is a genuine arrival: the meter answered, now, with its
+    current reading. Whether the NUMBER moved is irrelevant, so a healthy meter
+    under a flat load resets the age exactly like a busy one. Home Assistant
+    cannot provide this at all - it emits `state_changed` only on a change, does
+    not advance `last_reported` on either serialiser for a repeat, and refuses a
+    `state_reported` subscription outright ("Event filter is required"). Measured
+    on the ENV-01 rig over 70 s of a frozen meter, and independently against the
+    live house over ten repeated readings. So on `ha_signed` the age means "time
+    since the value changed", and our own capture of this house's meter has
+    42.2 s and 97.0 s between changes - both past the default `meter_max_age_s`
+    of 30, i.e. a false trip to 0 W on a perfectly healthy meter.
+
+    Everything else is TEL-01's pipeline unchanged: ingest timestamping,
+    `meter_max_age_s`, the clock-recomputed age, the plausibility bounds, and a
+    failed read treated as a MISSING reading rather than 0 W.
+
+    ⚠️ A failed or timed-out poll submits nothing. It is a rejection, so the
+    last good sample and its stamp stay exactly where they were and the age goes
+    on climbing - which is precisely the signal a dead meter should produce.
+
+    ⚠️ POLL CADENCE vs `meter_max_age_s`. The age can only be as fresh as the
+    poll interval, so `meter_poll_s` must sit well under `meter_max_age_s` or the
+    reading flaps in and out of staleness on a healthy meter. The real meter
+    updates every ~5.0 s (NOTES.md:640 measures 4.97 s), so polling faster than
+    that buys nothing but re-reads. Default 5 s against a 30 s max age; the
+    startup check in build_source refuses `meter_poll_s >= meter_max_age_s` and
+    warns past half of it.
+
+    ponytail: a plain `asyncio.sleep` loop rather than a scheduler, and no
+    backoff. A poll that fails costs one rejection and is retried on the next
+    tick; a meter that is down stays down and the age reports it. The ceiling is
+    a meter so slow that polls overlap - the request timeout is held under the
+    poll interval so they cannot.
+    """
+
+    def __init__(self, session, ingest: P1Ingest, host: str, *,
+                 port: int = HOMEWIZARD_PORT, poll_s: float = 5.0,
+                 timeout_s: float | None = None):
+        self.session = session
+        self.ingest = ingest
+        self.host, self.port = host, int(port)
+        self.poll_s = float(poll_s)
+        # ⚠️ Held under the poll interval on purpose: a timeout longer than the
+        # cadence queues polls behind a hung meter, and a backlog of requests
+        # all landing at once would stamp several arrivals for one measurement.
+        self.timeout_s = float(timeout_s) if timeout_s else max(1.0, self.poll_s * 0.8)
+        self.url = f"http://{self.host}:{self.port}{HOMEWIZARD_PATH}"
+        self.connected = False
+        self.polls = 0
+        self.poll_errors = 0
+        self._fingerprint: tuple | None = None
+        self._changed_mono: float | None = None
+
+    @property
+    def unchanged_s(self) -> float | None:
+        """Seconds since the meter last served a DIFFERENT measurement.
+
+        ⚠️ Diagnostic only, and deliberately NOT folded into
+        `sensor.p1_sample_age_s`. A frozen meter (SAFETY-01's six-minute
+        runaway) answers 200 OK with a stale document forever, so no arrival
+        detector can see it - only the document standing still can, and this is
+        that signal. It is exposed rather than acted on because it is NOT safe
+        as a 30 s watchdog input: this controller regulates grid power toward
+        ~0 W, and at a converged -10 W the export register takes six minutes to
+        advance by its 1 Wh resolution while the power figure legitimately
+        repeats. Thresholding that would rebuild the very limit cycle the
+        arrival stamp just removed, at the exact operating point we aim for.
+        Whoever wires a freeze detector must handle the low-power case first.
+        """
+        if self._changed_mono is None:
+            return None
+        return max(0.0, time.monotonic() - self._changed_mono)
+
+    async def run(self) -> None:
+        """Long-lived task: poll, submit, sleep, forever.
+
+        ⚠️ Nothing but cancellation may end this loop. An escaping exception
+        would kill the poll task for the lifetime of the add-on, and it would do
+        it QUIETLY: the failure mode is safe (no submissions, the age climbs, the
+        watchdog holds the battery at 0 W) but it looks identical to a dead
+        meter, so the operator goes hunting the wrong device. Retry on the next
+        tick instead - poll_s is already the retry cadence, so no backoff.
+        """
+        _LOG.info("P1 ingest: polling %s every %.1fs", self.url, self.poll_s)
+        while True:
+            try:
+                await self.poll_once()
+            except asyncio.CancelledError:
+                raise
+            except Exception as err:  # noqa: BLE001 - the task must outlive it
+                _LOG.warning("P1 meter poll %s: %s - retrying in %.1fs", self.url,
+                             str(err) or type(err).__name__, self.poll_s)
+            await asyncio.sleep(self.poll_s)
+
+    async def poll_once(self) -> bool:
+        """One GET. Returns True if a sample was accepted."""
+        self.polls += 1
+        try:
+            async with self.session.get(
+                    self.url,
+                    timeout=aiohttp.ClientTimeout(total=self.timeout_s)) as resp:
+                if resp.status != 200:
+                    raise P1Error(f"meter returned HTTP {resp.status}")
+                # content_type=None: the meter's own firmware is the authority on
+                # what it serves, and refusing a reading over a Content-Type
+                # header would be a fabricated outage.
+                # ⚠️ Kept because a real HomeWizard firmware that ever answers
+                # text/plain would otherwise read as a dead meter and hold the
+                # battery at 0 W. (This was once recorded here as an equivalent
+                # mutant - it is not. aiohttp's json_response always sets
+                # application/json, but web.Response(text=...) defaults to
+                # text/plain, so the fake meter CAN serve valid JSON under the
+                # wrong header, and test_p1.py now does.)
+                doc = await resp.json(content_type=None)
+        except asyncio.CancelledError:
+            raise
+        except Exception as err:  # noqa: BLE001 - any read failure is a gap
+            self.connected = False
+            self.poll_errors += 1
+            # ⚠️ str() of a bare asyncio.TimeoutError is the EMPTY STRING, so
+            # f"...: {err}" renders "last error:" and then nothing - on the
+            # status page, on a hung meter, at the moment the battery has just
+            # dropped to 0 W and someone is reading that line to find out why.
+            # The class name is the only thing that says "it timed out".
+            # ⚠️ str(err), not `err or ...`: an exception object is ALWAYS truthy,
+            # empty message or not, so the `or` would never reach the fallback.
+            self.ingest.reject(
+                f"meter poll {self.url}: {str(err) or type(err).__name__}")
+            return False
+
+        self.connected = True
+        try:
+            sample = parse_homewizard(doc, self.ingest.phases)
+            # ⚠️ Submitted unconditionally, INCLUDING a document identical to the
+            # last one. The response is the arrival; the number is not.
+            # Inside the try on purpose: submit() outside it would put a raise on
+            # a path with no handler at all, killing the poll task permanently -
+            # safely (the age climbs) but silently. run() backstops the rest.
+            self.ingest.submit(sample)
+            self._note(doc)
+        except P1Error as err:
+            self.ingest.reject(err)
+            return False
+        return True
+
+    def _note(self, doc) -> None:
+        fp = measurement_fingerprint(doc)
+        if self._changed_mono is None or fp != self._fingerprint:
+            self._fingerprint = fp
+            self._changed_mono = time.monotonic()
+
+
 # --------------------------------------------------------------------------- #
 # selection
 # --------------------------------------------------------------------------- #
@@ -683,15 +1044,133 @@ def is_enabled(opts: dict) -> bool:
     return str(opts.get("meter_source", "off") or "off").strip() not in ("off", "")
 
 
+def homewizard_host_port(opts: dict) -> tuple[str, str]:
+    """`p1_host` split into host and (still unparsed) port text.
+
+    One definition because validate_meter_options() and build_source() must
+    agree byte for byte about what counts as a usable address - a pasted browser
+    URL is the obvious way to fill this in wrong.
+    """
+    host = str(opts.get("p1_host", "") or "").strip()
+    host = host.removeprefix("http://").removeprefix("https://").rstrip("/")
+    host, _, port_s = host.partition(":")
+    return host, port_s
+
+
+def validate_meter_options(opts: dict, phases: int, max_age_s: float) -> list[str]:
+    """Every way `meter_source` can name a meter that will never produce a reading.
+
+    ⚠️ THIS IS THE ONLY PLACE THAT KNOWS THESE RULES. It used to be a run of
+    inline `return None`s inside build_source(); CFG-01 lifted them out because
+    the same predicates now have two callers with two different consequences:
+
+      validate.validate_startup_config()  refuses to start the add-on
+      build_source()                      returns None, as it always did
+
+    They are one function and not two on purpose. A second copy of "what makes a
+    meter config wrong" would drift, and the half that drifted would be the one
+    that decides whether the process is allowed to run.
+
+    Checked ONCE at startup rather than per telegram, because a misconfigured
+    source otherwise fails in the one way indistinguishable from a healthy source
+    nobody has sent anything to yet: no samples, a climbing age, the firmware
+    watchdog holding the battery at 0 W, and nothing in the log saying why.
+
+    Returns a list of human-readable problems; empty means the config is usable.
+    `phases` and `max_age_s` are passed in rather than read from opts so the
+    caller decides whether it is validating the options or an already-built
+    P1Ingest - build_source() has an ingest whose values may not have come from
+    this dict.
+    """
+    source = str(opts.get("meter_source", "off") or "off").strip()
+    if source in ("off", ""):
+        return []
+    problems: list[str] = []
+
+    if source == SOURCE_HA:
+        imp = str(opts.get("p1_import_entity", "") or "").strip()
+        exp = str(opts.get("p1_export_entity", "") or "").strip()
+        if not imp or not exp:
+            problems.append(
+                f"meter_source {SOURCE_HA} needs both p1_import_entity and "
+                f"p1_export_entity (got {imp or '<blank>'!r} / {exp or '<blank>'!r})")
+    elif source == SOURCE_HA_SIGNED:
+        net = str(opts.get("p1_net_entity", "") or "").strip()
+        phase_net = [str(e).strip() for e in
+                     (opts.get("p1_phase_net_entities") or []) if str(e).strip()]
+        if not net:
+            problems.append(
+                f"meter_source {SOURCE_HA_SIGNED} needs p1_net_entity "
+                "(sensor.p1_sample_age_s would otherwise be announced with "
+                "nothing feeding it)")
+        if phase_net and len(phase_net) != phases:
+            problems.append(
+                f"p1_phase_net_entities has {len(phase_net)} entities but "
+                f"meter_phases is {phases} - every telegram would be rejected "
+                "on the phase-count check")
+    elif source == SOURCE_MQTT:
+        if not str(opts.get("meter_mqtt_topic", "") or "").strip():
+            problems.append(f"meter_source {SOURCE_MQTT} needs meter_mqtt_topic")
+    elif source == SOURCE_HOMEWIZARD:
+        host, port_s = homewizard_host_port(opts)
+        if not host:
+            problems.append(
+                f"meter_source {SOURCE_HOMEWIZARD} needs p1_host (the meter's "
+                "own address, e.g. 192.168.2.250)")
+        if port_s:
+            try:
+                int(port_s)
+            except ValueError:
+                problems.append(f"p1_host {opts.get('p1_host')!r} has an "
+                                "unparseable port")
+        try:
+            # ⚠️ Not `or 5`: that turns an explicit 0 into the default, and a
+            # cadence of 0 is a misconfiguration that must be reported, not
+            # quietly corrected into something that looks like it was asked for.
+            raw = opts.get("meter_poll_s", 5)
+            poll_s = float(5 if raw is None or raw == "" else raw)
+        except (TypeError, ValueError):
+            problems.append(f"meter_poll_s {opts.get('meter_poll_s')!r} is not a number")
+        else:
+            if poll_s <= 0:
+                problems.append("meter_poll_s must be positive")
+            # ⚠️ The age can never be fresher than the poll interval. At or past
+            # max_age_s every reading is stale before its successor arrives, so
+            # the controller would sit permanently on missing inputs while the
+            # meter is perfectly healthy - refuse it rather than ship that.
+            elif poll_s >= max_age_s:
+                problems.append(
+                    f"meter_poll_s {poll_s:.1f} is not under meter_max_age_s "
+                    f"{max_age_s:.1f} - every reading would go stale before the "
+                    "next poll")
+    else:
+        problems.append(
+            f"meter_source {source!r} is not one of "
+            + ", ".join((SOURCE_HA, SOURCE_MQTT, SOURCE_HA_SIGNED, SOURCE_HOMEWIZARD)))
+    return problems
+
+
 def build_source(opts: dict, ingest: P1Ingest, session, broker: dict | None):
     """Return the transport named by `meter_source`, or None if disabled.
 
     This is the whole of AC 1's "switchable": every consumer reads P1Ingest, so
     changing transport is a config edit, never a code path.
+
+    ⚠️ In the add-on this is now unreachable with a bad config -
+    validate_startup_config() refuses to start on anything
+    validate_meter_options() rejects. The guard stays because this function is
+    also called directly by tests and by anything embedding P1Ingest, and
+    "returns None" is a safer default for those callers than a transport that
+    can never read.
     """
     source = str(opts.get("meter_source", "off") or "off").strip()
     if not is_enabled(opts):
         return None
+    problems = validate_meter_options(opts, ingest.phases, ingest.max_age_s)
+    if problems:
+        for problem in problems:
+            _LOG.error("%s - P1 ingestion disabled", problem)
+        return None
     if source == SOURCE_HA:
         return HaDsmrSource(session, ingest, {
             "import": opts.get("p1_import_entity", ""),
@@ -699,12 +1178,29 @@ def build_source(opts: dict, ingest: P1Ingest, session, broker: dict | None):
             "phase_import": opts.get("p1_phase_import_entities") or [],
             "phase_export": opts.get("p1_phase_export_entities") or [],
         })
+    if source == SOURCE_HA_SIGNED:
+        return HaSignedSource(session, ingest, {
+            "net": str(opts.get("p1_net_entity", "") or "").strip(),
+            "phase_net": [str(e).strip() for e in
+                          (opts.get("p1_phase_net_entities") or []) if str(e).strip()],
+        })
+    if source == SOURCE_HOMEWIZARD:
+        host, port_s = homewizard_host_port(opts)
+        port = int(port_s) if port_s else HOMEWIZARD_PORT
+        raw = opts.get("meter_poll_s", 5)
+        poll_s = float(5 if raw is None or raw == "" else raw)
+        # A warning, not a refusal: one missed poll costs a stale reading and a
+        # 0 W cycle, which is fail-safe. The refusal above is for cadences that
+        # can NEVER be fresh.
+        if poll_s > ingest.max_age_s / 2:
+            _LOG.warning("meter_poll_s %.1f leaves no room under meter_max_age_s "
+                         "%.1f: one missed poll makes the reading stale. The meter "
+                         "updates every ~5 s; 5 s against 30 s is the tested pair.",
+                         poll_s, ingest.max_age_s)
+        return HomeWizardLocalSource(session, ingest, host, port=port, poll_s=poll_s)
     if source == SOURCE_MQTT:
         broker = broker or {}
         return MqttP1Source(ingest, str(opts.get("meter_mqtt_topic", "")),
                             broker.get("host"), broker.get("port", 1883),
                             broker.get("username"), broker.get("password"))
-    if source:
-        _LOG.error("meter_source %r is not %s or %s - P1 ingestion disabled",
-                   source, SOURCE_HA, SOURCE_MQTT)
     return None

goodwe_controller/app/validate.py

@@ -0,0 +1,315 @@
+"""Startup configuration validation - the gate before the control loop runs.
+
+WHAT THIS IS FOR, in one sentence: some configurations are not "a bit off", they
+are configurations under which the add-on's own safety machinery does not work,
+and for those the correct behaviour is to refuse to start rather than to log a
+line and carry on.
+
+⚠️ THE FAILURE THIS REPLACES. `main.py` used to read the setpoint device's own
+±5000 W rating, notice that a configured `max_w` of, say, 8000 W exceeded it,
+write one WARNING to a log nobody reads, and then run anyway with
+`write_setpoint()` quietly clamping. The operator's stated ceiling was simply not
+the ceiling, and the only evidence was a line that had scrolled off. specs §1.5
+is explicit that a configuration in which the system cannot honour what it was
+told is refused at startup, not survived at runtime.
+
+WHERE THE LINE IS DRAWN, and why it is not further out. A validator that refuses
+on trivia gets switched off by the first person it inconveniences, so this one
+refuses only where **continuing produces one of two outcomes:**
+
+  (a) **a stated limit is untrue** - the operator configured a bound, a lower
+      layer silently enforces a different one, and nothing says which won; or
+  (b) **the add-on is inert and indistinguishable from healthy** - it starts,
+      serves its UI, reports green, and moves no energy, with no symptom that
+      separates it from a correctly-idle system.
+
+⚠️ (b) IS NOT A SPECIAL CASE OF (a), and an earlier draft of this file wrongly
+implied it was by claiming every refusal here "makes a safety mechanism
+inoperative". It does not: when `setpoint_entity` is blank, layer 1 pinning the
+inverter at 0 W is the failsafe WORKING. The problem is not that the system
+becomes unsafe, it is that it becomes a very convincing impression of a working
+controller - and an operator has no way to tell. That is its own reason to
+refuse, and stating it as one is what stops the rule being stretched later to
+cover mere untidiness.
+
+Both halves have to stay narrow. (a) is not "any two numbers that could
+disagree"; it is a bound the operator SET being overridden by a layer they
+cannot see. (b) is not "anything degraded"; it is inert AND silent - if a red
+NOT READY banner already names the problem, (b) does not apply.
+
+  1. `max_w` outside the setpoint device's own rating.  [(a)]
+     The stated limit is untrue. arbiter.py's `supervised` SAFETY claim says the
+     output is bounded by ±max_w; it is not, it is bounded by the device, and the
+     two numbers disagree. Which one wins is a coin toss to anyone reading the
+     config.
+
+  2. No `setpoint_entity`.  [(b)]
+     A controller with no actuator, and nothing about it looks broken.
+     `write_setpoint()` returns immediately on a blank entity, so: no device
+     rating is ever read (the `device` SAFETY claim is never made at all), and
+     the ESP32 heartbeat - the thing that feeds LAYER 1 - never happens. The
+     add-on serves a UI, publishes MQTT, resolves claims, and moves nothing.
+     Layer 1 then holds the inverter at 0 W, which is the failsafe working
+     exactly as designed - this is (b), not (a). Nothing is unsafe; it is simply
+     impossible to tell from the outside that the thing is doing nothing.
+
+  3. A `meter_source` that can never produce a reading.  [(b)]
+     §5.1 makes P1 the only authoritative measurement and deliberately provides
+     no fallback, so a transport that cannot be built means `grid` is None
+     forever: permanent "inputs missing", 0 W, and a status page that reports a
+     meter with a climbing age exactly as it would for a healthy meter nobody has
+     sent anything to yet. The predicates live in `p1.validate_meter_options()`,
+     which is also what `build_source()` uses - one definition, two callers.
+
+  4. `meter_max_age_s` above the firmware's own ingest veto.  [(a)]
+     The purest example of (a) in the system, and structurally the same fault as
+     1. The add-on's schema accepts `int(5,300)`. The firmware's threshold is a
+     COMPILE-TIME SUBSTITUTION - `max_age_s: "30"` in
+     goodwe-master-stage4-failsafe.yaml - used by both its monotonic receipt
+     clock and its `ingest_stale` veto, which trips layer 1 on
+     `p1_age_s >= 30`. Set 120 and the add-on believes a 119 s reading is fresh
+     and keeps commanding into it, while the firmware vetoed at 30 s and is
+     holding the inverter at 0 W. Status page: healthy meter, running
+     controller, nothing moving, and no line anywhere saying the number you set
+     was overruled. That firmware file's own comment says a lower bound on this
+     "belongs in CFG-01, not here" - so here it is.
+
+  5. `sign_disagree_w` at or above `max_w`.  [(a)]
+     The arbiter's `supervised` limit bounds every command to +-max_w, and
+     SAFETY-02's predicate needs `abs(command) > sign_disagree_w`. Set the
+     threshold at or above the ceiling and the command side of the comparison
+     is unsatisfiable BY CONSTRUCTION: the watchdog can never fire, on any
+     input, ever. Same shape as 1 and 4 - the operator set a number, a layer
+     they cannot see makes it mean something else, and nothing says so. Worse
+     here, because what the status page reports in that state is "sign
+     watchdog: armed". A disarmed guard that advertises itself as armed is the
+     one thing this project has decided repeatedly it will not ship.
+
+WHAT IS DELIBERATELY *NOT* REFUSED, because it is untidy rather than unsafe:
+
+  - `integrator_max_w` above `max_w`. DOCS.md is right that the only thing the
+    extra headroom buys is more wrong-direction power to unwind after
+    saturation - but the arbiter's `supervised` limit still binds the wire to
+    ±max_w, so nothing out of range ever reaches the inverter. The cost is
+    latency, not amperage. Warned about, not refused.
+  - A missing `soc_entity` / `batt_entity`. `inputs_ok` goes False, the loop
+    commands 0 W, and `checks()` already renders a red NOT READY banner naming
+    the missing entity. Fail-safe AND already loud; a refusal adds nothing.
+  - A `setpoint_entity` that exists in the config but is not found on the Core
+    API at startup. This is the transient case - ESPHome is frequently not up
+    yet when the add-on boots - and refusing here would turn a device that
+    arrives thirty seconds late into a restart loop needing a human. It stays a
+    NOT READY banner.
+  - `meter_poll_s` above half `meter_max_age_s`. One missed poll costs a stale
+    reading and a 0 W cycle. Warned about in p1.py, not refused.
+"""
+
+import logging
+
+from .p1 import is_enabled, validate_meter_options
+
+_LOG = logging.getLogger("goodwe.config")
+
+# ⚠️ A MIRROR OF A FIRMWARE CONSTANT, AND IT CANNOT BE IMPORTED. The firmware
+# threshold is a compile-time YAML substitution baked into the ESP32 image
+# (`max_age_s: "30"`, master/goodwe-master-stage4-failsafe.yaml), so nothing at
+# runtime can ask the board what value it was built with. This number is a copy,
+# and a copy of a constant in another repo is a thing that goes stale.
+#
+# What makes that acceptable here: the copy can only ever be WRONG IN THE SAFE
+# DIRECTION for the check below. If the firmware's veto is raised above 30, this
+# refuses some configs that would in fact have worked - annoying, visible
+# immediately, and fixed by editing one line. It cannot start accepting a config
+# the firmware vetoes unless the firmware's number goes DOWN, which would be a
+# tightening nobody does silently.
+#
+# ⚠️ TEL-06 IS EDITING `ingest_stale` DIRECTLY. If that ticket changes what the
+# veto MEANS - e.g. thresholding arrival rather than the sensor's value - this
+# constant's justification has to be re-read, not just its number. Do not assume
+# a matching integer means a matching rule.
+FIRMWARE_INGEST_VETO_S = 30.0
+
+# ⚠️ The complete set of option keys through which this add-on can reach an
+# actuator. specs §1.5 makes "any configuration in which two writers can reach
+# one actuator" a non-goal, and the way that non-goal is ENFORCED here is by
+# construction: there is exactly one such key, so a second writer is not
+# expressible in the options schema at all. sim/inject.py's `two_writers`
+# scenario asserts on this tuple - if a second write path is ever added, that
+# scenario goes red and somebody has to decide how the two are arbitrated
+# BEFORE the config that allows both can ship.
+ACTUATOR_WRITE_KEYS = ("setpoint_entity",)
+
+
+class ConfigRefused(Exception):
+    """The configuration is wrong. Not "something broke" - see main.py's handler.
+
+    Carries the list of problems so the caller can render them; str() is the
+    first one, so an unhandled traceback still names something useful.
+    """
+
+    def __init__(self, problems: list[str]):
+        self.problems = problems
+        super().__init__(problems[0] if problems else "configuration refused")
+
+
+def validate_startup_config(opts: dict, dev_min=None, dev_max=None) -> list[str]:
+    """Return the list of reasons this configuration must not be started.
+
+    Empty list means go. `dev_min`/`dev_max` are the setpoint device's own
+    reported range (`hass.limits()`), or None when the device could not be
+    reached - in which case the range checks are skipped rather than guessed at,
+    for the transient reason in this module's docstring.
+
+    Pure and side-effect free apart from two warnings, so it can be called from
+    a test or from sim/inject.py without a Home Assistant anywhere near it.
+    """
+    problems: list[str] = []
+
+    # --- 1. an actuator to write to ------------------------------------------
+    writers = [k for k in ACTUATOR_WRITE_KEYS
+               if str(opts.get(k, "") or "").strip()]
+    if not writers:
+        problems.append(
+            "setpoint_entity is not set, so this add-on has no actuator: every "
+            "write is a no-op, the device's own rating is never read, and the "
+            "ESP32 heartbeat that holds off the layer-1 failsafe never happens. "
+            "It would run, look healthy, and move no energy at all. Set it to "
+            "the ESPHome number entity that carries the setpoint.")
+
+    # --- 2. the configured ceiling against the device's own rating -----------
+    max_w = _number(opts, "max_w", 2000.0)
+    if max_w is None:
+        problems.append(f"max_w {opts.get('max_w')!r} is not a number")
+    # ⚠️ config.yaml's int(100,5000) already blocks this on a real install, so
+    # the check is not for the Supervisor path - it is because
+    # validate_startup_config() is now also sim/inject.py's entry point and can
+    # be handed any dict at all. A max_w of 0 or below inverts the arbiter's
+    # `supervised` bounds (lo=-max_w becomes the HIGHER number), and a limit
+    # claim whose lo exceeds its hi is exactly the contradiction the arbiter
+    # resolves to 0 W - i.e. it would look like a safety trip rather than the
+    # nonsense config it is.
+    elif max_w <= 0:
+        problems.append(
+            f"max_w is {max_w:.0f} W and must be positive - it is a magnitude, "
+            "not a signed setpoint. At or below zero the arbiter's supervised "
+            f"limit becomes lo={-max_w:.0f} / hi={max_w:.0f}, which is a "
+            "contradiction it resolves to 0 W, so the controller would look "
+            "like it was tripping rather than misconfigured.")
+    elif dev_max is not None and max_w > dev_max:
+        problems.append(
+            f"max_w is {max_w:.0f} W but {opts.get('setpoint_entity') or 'the setpoint device'} accepts at "
+            f"most {dev_max:.0f} W - THE DEVICE WINS, so the {max_w:.0f} W you "
+            f"configured would silently never happen. Lower max_w to "
+            f"{dev_max:.0f} W or less, or point setpoint_entity at a device that "
+            f"can take {max_w:.0f} W.")
+    elif dev_min is not None and -max_w < dev_min:
+        problems.append(
+            f"max_w is {max_w:.0f} W, so this controller may command "
+            f"{-max_w:.0f} W, but {opts.get('setpoint_entity') or 'the setpoint device'} accepts no less "
+            f"than {dev_min:.0f} W - THE DEVICE WINS on the charge side. Lower "
+            f"max_w to {abs(dev_min):.0f} W or less.")
+
+    # --- 3. a meter that can actually read -----------------------------------
+    # ⚠️ Not a second copy of these rules - p1.py owns them, because
+    # build_source() has to apply the identical predicates and a drifted copy
+    # would be worse than no check.
+    phases = _number(opts, "meter_phases", 1.0)
+    max_age_s = _number(opts, "meter_max_age_s", 30.0)
+    if phases is None or max_age_s is None:
+        problems.append("meter_phases and meter_max_age_s must both be numbers "
+                        f"(got {opts.get('meter_phases')!r} / "
+                        f"{opts.get('meter_max_age_s')!r})")
+    else:
+        problems.extend(validate_meter_options(opts, int(phases), max_age_s))
+
+    # --- 4. the staleness window the FIRMWARE will actually enforce -----------
+    # ⚠️ Only when P1 ingestion is on, and that is a real scope limit rather than
+    # caution: meter_max_age_s is read by nothing but P1Ingest, and the veto it
+    # collides with keys off `p1_age_s.has_state()`, which is only ever published
+    # when ingestion is running (see Controller.publish()). With meter_source off
+    # there is no sensor, the veto is inert, and the number governs nothing.
+    #
+    # Strictly greater, not >=: the firmware trips at `>= 30` and P1Ingest goes
+    # stale at `> max_age_s`, so 30 against 30 has the firmware fractionally
+    # stricter by one sample. That is the shipped default and the tested pair.
+    # BELOW 30 is fine and deliberately not refused - the add-on then gives up
+    # first, which is fail-safe and visible on its own status page. Only ABOVE is
+    # the silent case, where the add-on keeps commanding into a reading the board
+    # has already rejected.
+    if (is_enabled(opts) and max_age_s is not None
+            and max_age_s > FIRMWARE_INGEST_VETO_S):
+        problems.append(
+            f"meter_max_age_s is {max_age_s:.0f} s but the ESP32 firmware vetoes "
+            f"any P1 sample at {FIRMWARE_INGEST_VETO_S:.0f} s and forces the "
+            "layer-1 failsafe - THE FIRMWARE WINS, and it wins silently. This "
+            f"add-on would treat a {max_age_s - 1:.0f} s reading as fresh and "
+            "keep commanding, while the inverter sat at 0 W with a healthy-"
+            "looking meter on the status page. Lower meter_max_age_s to "
+            f"{FIRMWARE_INGEST_VETO_S:.0f} s or less (30 s is the tested value), "
+            "or rebuild the firmware with a matching max_age_s and update "
+            "validate.FIRMWARE_INGEST_VETO_S.")
+
+    # --- 5. a sign watchdog that can actually fire ---------------------------
+    # ⚠️ Strictly `>=`, matching the predicate exactly: watchdog.py tests
+    # `abs(commanded_w) > min_w`, and the arbiter holds `abs(commanded_w)` at or
+    # below max_w, so threshold == max_w is already unsatisfiable. Anything
+    # BELOW max_w is reachable and therefore fine - this refuses the disarmed
+    # case only, not "close to the rail".
+    sign_w = _number(opts, "sign_disagree_w", 300.0)
+    if sign_w is None:
+        problems.append(f"sign_disagree_w {opts.get('sign_disagree_w')!r} is not a number")
+    elif max_w is not None and max_w > 0 and sign_w >= max_w:
+        problems.append(
+            f"sign_disagree_w is {sign_w:.0f} W but max_w is {max_w:.0f} W, so "
+            "the SAFETY-02 sign-disagreement watchdog can never fire: the "
+            "arbiter never lets a command exceed max_w, and the watchdog needs "
+            f"a command over {sign_w:.0f} W. It would sit there reporting "
+            "'armed' on the status page while being incapable of tripping - the "
+            f"one runaway failure mode this system has actually observed. Lower "
+            f"sign_disagree_w below {max_w:.0f} W (300 W is the measured "
+            "default), or raise max_w.")
+
+    # --- warnings: real, but not worth refusing over -------------------------
+    integ = opts.get("integrator_max_w")
+    integ_w = None if not integ else _number(opts, "integrator_max_w", None)
+    if integ_w is not None and max_w is not None and integ_w > max_w:
+        _LOG.warning(
+            "integrator_max_w %.0f W is above max_w %.0f W. Not refused - the "
+            "arbiter still bounds the wire to +-max_w - but the only thing the "
+            "extra headroom buys is more wrong-direction power to unwind after "
+            "saturation. 0 (follow max_w) is the recommended value.",
+            integ_w, max_w)
+
+    return problems
+
+
+def _number(opts: dict, key, default):
+    raw = opts.get(key, default)
+    if raw is None or raw == "":
+        return default
+    try:
+        return float(raw)
+    except (TypeError, ValueError):
+        return None
+
+
+def refuse(problems: list[str]) -> None:
+    """Log a refusal an operator can tell apart from a crash. Does not raise.
+
+    ⚠️ THE POINT OF THE BANNER. "You configured this wrong" must not read like
+    "it broke". A Python traceback in an add-on log means the same thing to most
+    operators as a segfault - file a bug - whereas this block names the keys,
+    names the fix, and says in words that nothing is broken. main.py catches
+    ConfigRefused and exits 78 (sysexits EX_CONFIG), so no traceback is printed
+    at all and even the exit status distinguishes the two.
+    """
+    _LOG.error("=" * 72)
+    _LOG.error("REFUSING TO START: the add-on configuration is not usable.")
+    _LOG.error("This is a CONFIGURATION problem, not a crash. Nothing is broken;")
+    _LOG.error("the add-on will start as soon as the settings below are fixed.")
+    _LOG.error("Fix them in Settings > Add-ons > GoodWe RS485 Controller >")
+    _LOG.error("Configuration, then start the add-on again.")
+    _LOG.error("-" * 72)
+    for i, problem in enumerate(problems, 1):
+        _LOG.error("  %d. %s", i, problem)
+    _LOG.error("=" * 72)

goodwe_controller/app/watchdog.py

@@ -0,0 +1,220 @@
+"""SAFETY-02 - the sign-disagreement watchdog.
+
+WHAT IT CATCHES, in one sentence: a grid-following loop that is pushing power in
+the wrong direction, which every other guard in this system is blind to.
+
+The stale-input watchdog (SAFETY-01) asks "is the meter still talking?". The
+saturation freeze asks "can the inverter follow?". The output clamp asks "is the
+number too big?". A loop can pass all three and still be charging the battery
+out of the grid while the house imports - the meter is fresh, the inverter is
+tracking beautifully, and the magnitude is inside the rating. The only thing
+that separates that from healthy operation is the SIGN.
+
+⚠️ THIS IS NOT A HYPOTHETICAL. On 2026-08-20 the vendor controller (Illusmart)
+did exactly this four times in one day (NOTES.md §4.7). Both captures of that
+bus are committed - `sim/scenarios/bus-2026-08-20.log.gz` and the healthy
+`bus-2026-08-23.log.gz` in the infra repo - and `sim/replay_sign.py` drives this
+module over both of them. Every number in this file was measured on those two
+days, not chosen:
+
+    day          samples gated in    sign agreement
+    2026-08-23   4 127 / 16 349      92.9 %   (healthy)
+    2026-08-20   6 892 / 15 598      55.6 %   (the whole fault day)
+      episode A  15:26-16:43            0.3 %
+      episode B  17:11-18:28            0.8 %
+      episode C  20:01-20:31           11.0 %
+      episode D  20:55-21:11            0.0 %
+
+That is the signature, and it is the SAME signature in all four episodes: not a
+noisier version of healthy, a near-total inversion.
+
+------------------------------------------------------------------------------
+WHY IT LIVES HERE AND NOT IN THE FIRMWARE OR THE WITNESS
+
+Three vantage points see three different things. The firmware knows what it
+WROTE, the witness Pi knows what was ON THE WIRE and whether the inverter ACKed
+it, and the add-on knows what it INTENDED and holds the authoritative meter.
+
+This check is not command-versus-wire; it is command-versus-physics. It needs
+the emitted setpoint and the P1 net figure in the same place, and it needs the
+authority to command zero when they fight:
+
+  - the witness is read-only by charter and cannot command anything, so it could
+    raise the alarm but never take the trip action the AC requires;
+  - the firmware has the wire but not the meter. §5.1 makes P1 the only
+    authoritative grid figure and the board only ever receives its AGE
+    (`sensor.goodwe_p1_sample_age`), never its value. Putting the check there
+    would mean shipping the meter to the ESP32 for no other reason, and it would
+    be C++ per install rather than one generic guard;
+  - the add-on has both halves already, plus an arbiter that can outrank every
+    strategy with a P_SAFETY claim.
+
+The cost of standing here is real and worth stating: this watchdog compares what
+we MEANT to put on the wire against the meter. If the firmware or the driver
+inverts the sign on the way out, the add-on's own view still agrees with itself
+and this check stays silent. That gap is a wire-versus-intent problem and it
+belongs to the witness, not here.
+
+------------------------------------------------------------------------------
+WHAT "DISAGREEMENT" MEANS, PRECISELY
+
+    disagree = following
+               and commanded_w * grid_w < 0
+               and abs(commanded_w) > min_w
+               and abs(grid_w)      > min_w
+
+Four gates, and each one exists to exclude a specific thing that is NOT a fault:
+
+1. `following`. ⚠️ THE GATE THAT IS EASIEST TO FORGET AND MOST EXPENSIVE TO
+   OMIT. Sign agreement is a property of a GRID-FOLLOWING loop. It is not
+   expected of a strategy that deliberately commands against the meter -
+   maintenance is exactly that. A maintenance grid charge of 2500 W into a house
+   drawing 500 W puts +3000 W on the meter against a -2500 W command: opposed,
+   both far over any sane threshold, and sustained for HOURS. Armed
+   unconditionally this watchdog would trip on every single maintenance cycle,
+   which is not a tuning problem, it is the wrong question being asked. So the
+   caller says whether the grid-following loop actually won the arbitration this
+   cycle, and the timer only accumulates when it did.
+
+2. The strict `< 0` product. "Opposed" and "neither side is zero" in one
+   expression.
+
+3. The 300 W magnitude gate ON BOTH SIDES. Near zero the sign is noise, and near
+   zero is where a healthy loop LIVES - the deadband holds the command still
+   while the meter wanders either side of `target_grid_w`. On the healthy day
+   only 4 127 of 16 349 samples (25 %) are even gated in; the other 75 % are the
+   converged band where sign carries no information. This is also why the
+   deadband cannot produce a false trip: inside it the meter is by definition
+   under 300 W.
+
+4. The 180 s continuity requirement. This is what excludes the legitimate
+   transient. A load step reverses the meter's sign instantly while the command
+   is still where the last cycle left it; slew limiting then needs a few cycles
+   to cross over. Measured on the healthy day, the LONGEST such crossing is 30 s
+   - and that is with a vendor controller far cruder than ours. 180 s is six
+   times that. It is not a fitted threshold: at 60 s the healthy day still
+   produces zero trips, and at 300 s the fault day still produces 13.
+
+⚠️ A BATTERY THAT REFUSES A COMMAND CANNOT TRIP THIS, and that is structural
+rather than lucky. At SoC 10 % in Standby, a 1350 W discharge command into a
+1350 W import is DECLINED: the battery does nothing, so the meter stays at
++1350 W and the command stays at +1350 W. Same sign. Agreement. A refusal leaves
+the meter where it was; only the inverter ACTING moves it, and acting in the
+commanded direction moves it toward zero, not through it. The failure mode this
+check keys on is the opposite of a refusal - it is the inverter obediently doing
+a wrong thing.
+
+⚠️ A FROZEN METER cannot trip it either, for the same reason read the other way:
+a stuck reading of +800 W makes the loop command discharge and keep commanding
+discharge. Command and meter converge on AGREEING. Freezes are SAFETY-12's and
+SAFETY-01's problem, and this watchdog neither helps nor hinders there.
+
+------------------------------------------------------------------------------
+STATE, TRIP AND LATCH
+
+One timestamp, not a sample counter. The cycle rate is not fixed - a meter
+arrival, or `cycle_floor_s` elapsing, whichever comes first - so N samples is a
+different wall-clock window on every path, and the AC is written in minutes.
+
+The latch is not optional and not a nicety. Commanding 0 W removes the command
+side of the comparison (|0| is not > 300), so the disagreement disappears the
+instant the trip works. Un-latched, this watchdog would trip, clear itself, and
+hand the actuator straight back to the loop that was driving the wrong way -
+three minutes later, forever. `tripped` therefore stays true until an operator
+`reset()`s it by starting control again, which is a deliberate human act after
+looking at why.
+"""
+
+from dataclasses import dataclass
+from datetime import datetime
+
+
+@dataclass(frozen=True)
+class SignWatchdogConfig:
+    """Defaults, not constants - config.yaml carries both (SAFETY-02 AC 5)."""
+
+    min_w: float = 300.0
+    hold_s: float = 180.0
+
+
+class SignWatchdog:
+    """One instance per actuator, evaluated once per control cycle.
+
+    ⚠️ NOT SHARED ACROSS CADENCES. `disagree_since` is a wall-clock start time,
+    so driving one instance from two loops at two rates would have each one
+    resetting the other's window. If a fast on-device path ever wants this
+    check, it gets its own instance - the same exactly-one-writer discipline the
+    arbiter applies to the actuator, applied to the detector's own state.
+    """
+
+    def __init__(self, cfg: SignWatchdogConfig | None = None):
+        self.cfg = cfg or SignWatchdogConfig()
+        self.disagree_since: datetime | None = None
+        self.tripped = False
+        self.reason = ""
+
+    # -- the whole check, and it is a pure function of its arguments ----------
+    def evaluate(self, commanded_w, grid_w, following: bool,
+                 now: datetime) -> bool:
+        """Advance the detector one cycle. Returns True while tripped.
+
+        `commanded_w`  the EMITTED setpoint - what is standing on the wire now,
+                       after deadband, slew, quantisation and the arbiter. Not
+                       the optimizer's raw wish: the wire carries the emitted
+                       value, so anything else can disagree with the meter for a
+                       reason that is not a fault.
+        `grid_w`       net P1, + = importing. None when the meter is stale or
+                       missing, which CLEARS the timer rather than accumulating
+                       - a frozen figure held against a moving command would
+                       otherwise manufacture a disagreement in about three
+                       minutes, on top of SAFETY-01 having already commanded
+                       zero for the same cause.
+        `following`    did the grid-following loop actually win this cycle? See
+                       gate 1 in the module docstring.
+        `now`          the caller's clock, so this stays testable and replayable.
+        """
+        if self.tripped:
+            # Latched. Do not re-evaluate: the trip removed the evidence.
+            return True
+
+        cfg = self.cfg
+        disagree = (
+            following
+            and commanded_w is not None and grid_w is not None
+            and commanded_w * grid_w < 0
+            and abs(commanded_w) > cfg.min_w
+            and abs(grid_w) > cfg.min_w
+        )
+
+        if not disagree:
+            self.disagree_since = None
+            return False
+
+        if self.disagree_since is None:
+            self.disagree_since = now
+            return False
+
+        held = (now - self.disagree_since).total_seconds()
+        if held < cfg.hold_s:
+            return False
+
+        self.tripped = True
+        self.reason = (
+            f"SIGN_DISAGREEMENT: commanded {commanded_w:+.0f} W against a meter "
+            f"reading {grid_w:+.0f} W for {held:.0f} s continuously "
+            f"(limits: both over {cfg.min_w:.0f} W, held over {cfg.hold_s:.0f} s)"
+        )
+        return True
+
+    @property
+    def held_s(self) -> float:
+        """How long the current disagreement has been standing, for the UI."""
+        if self.disagree_since is None:
+            return 0.0
+        return (datetime.now(self.disagree_since.tzinfo)
+                - self.disagree_since).total_seconds()
+
+    def reset(self) -> None:
+        self.disagree_since = None
+        self.tripped = False
+        self.reason = ""

goodwe_controller/config.yaml

@@ -1,5 +1,5 @@
 name: GoodWe RS485 Controller
-version: "0.2.1"
+version: "0.5.0"
 slug: goodwe_controller
 description: >-
   Drives a GoodWe ES/BP battery inverter over RS485 by emulating its smart
@@ -42,11 +42,24 @@ options:
   # --- P1 meter ingestion (specs §5.2 / §14 `meter:`) -------------------------
   # `off` keeps the original single meter_entity path above, so an existing
   # install is untouched until it opts in. ha_dsmr subscribes to the DSMR
-  # integration's entities over the HA WebSocket; mqtt_p1 reads the topic below.
+  # integration's entities over the HA WebSocket; mqtt_p1 reads the topic below;
+  # ha_signed reads ONE signed HA entity (+ import / - export), which is what a
+  # HomeWizard P1 publishes and what ha_dsmr cannot consume.
+  # homewizard_local skips Home Assistant entirely and polls the meter's own
+  # local API. ⚠️ It is the ONLY mode whose sensor.p1_sample_age_s measures when
+  # the meter REPORTED rather than when the value last CHANGED - HA emits
+  # nothing at all for a repeated reading - so it is the only mode a firmware
+  # watchdog may threshold. See DOCS.md.
   meter_source: "off"
   meter_phases: 1
   meter_max_age_s: 30
   meter_mqtt_topic: ""
+  # homewizard_local only. The meter's own address, `host` or `host:port`.
+  p1_host: ""
+  # homewizard_local only. Seconds between polls. Must be well under
+  # meter_max_age_s - the age is never fresher than this interval - and there is
+  # nothing to gain below the meter's own ~5.0 s update rate (NOTES.md:640).
+  meter_poll_s: 5
   # The two UNSIGNED Belgian registers. The EMS derives net power from them
   # (import - export); do NOT point these at a signed template sensor.
   p1_import_entity: ""
@@ -55,6 +68,15 @@ options:
   # three-phase connection; the list length must equal meter_phases.
   p1_phase_import_entities: []
   p1_phase_export_entities: []
+  # ha_signed only. ONE signed net-power sensor: positive = import from the
+  # grid, negative = export to it. Do NOT split it into two template sensors -
+  # the split is done in the add-on (p1.split_signed) precisely so the sign
+  # convention is tested rather than living in unreviewed YAML.
+  p1_net_entity: ""
+  # Optional, in L1..L3 order, each one signed the same way. Same role as
+  # p1_phase_import_entities: the capacity-tariff peak on a three-phase
+  # connection. The list length must equal meter_phases.
+  p1_phase_net_entities: []
 
   # --- control ---------------------------------------------------------------
   max_w: 2000
@@ -68,8 +90,30 @@ options:
   integrator_max_w: 0
   heartbeat_s: 10
   stale_input_s: 15
+  cycle_floor_s: 15
   auto_start: false
 
+  # --- SAFETY-02 sign-disagreement watchdog ----------------------------------
+  # Trips when the emitted setpoint and the P1 net figure point OPPOSITE ways,
+  # both over sign_disagree_w, continuously for sign_disagree_s. Action: 0 W and
+  # a failsafe that latches until an operator starts control again.
+  #
+  # Both defaults are measured, not chosen. On the captured healthy day
+  # (2026-08-23) the longest legitimate opposed run - a load step the loop has
+  # not caught up with - is 30 s, and sign agreement over the gated samples is
+  # 92.9 %. On the captured fault day (2026-08-20) the four episodes run 0.0-11 %
+  # agreement with opposed runs up to 1752 s. 300 W / 180 s sits in the middle of
+  # a very wide gap: at 60 s the healthy day still trips nothing, at 300 s the
+  # fault day still trips 13 times. There is no reason to move either number
+  # without a capture that says so. They are options because the AC says
+  # thresholds are defaults rather than constants - not because they are knobs
+  # anyone is expected to turn.
+  #
+  # ⚠️ sign_disagree_w must stay BELOW max_w or the watchdog can never fire (the
+  # arbiter bounds the command to +-max_w). validate.py refuses that config.
+  sign_disagree_w: 300
+  sign_disagree_s: 180
+
   # --- maintenance -----------------------------------------------------------
   maintenance_enabled: false
   maintenance_interval_days: 28
@@ -98,20 +142,25 @@ schema:
   batt_invert: bool
   setpoint_entity: str
 
-  meter_source: list(off|ha_dsmr|mqtt_p1)
+  meter_source: list(off|ha_dsmr|mqtt_p1|ha_signed|homewizard_local)
   # ⚠️ 2 is accepted by this range but is not a real Belgian connection. A
   # telegram whose phase count disagrees is rejected at ingest and logged, so a
   # mis-set 2 shows up immediately as "0 telegrams accepted" rather than as a
   # quietly wrong number.
   meter_phases: int(1,3)
   meter_max_age_s: int(5,300)
+  meter_poll_s: int(1,60)
   meter_mqtt_topic: str?
+  p1_host: str?
   p1_import_entity: str?
   p1_export_entity: str?
   p1_phase_import_entities:
     - str
   p1_phase_export_entities:
     - str
+  p1_net_entity: str?
+  p1_phase_net_entities:
+    - str
 
   max_w: int(100,5000)
   gain: float(0.05,1.0)
@@ -124,8 +173,14 @@ schema:
   integrator_max_w: int(0,15000)
   heartbeat_s: int(2,25)
   stale_input_s: int(5,120)
+  cycle_floor_s: int(5,60)
   auto_start: bool
 
+  # No "off" value, deliberately: this is a P0 safety check and the schema is
+  # not the place to make disarming it a supported configuration.
+  sign_disagree_w: int(50,5000)
+  sign_disagree_s: int(30,1800)
+
   maintenance_enabled: bool
   maintenance_interval_days: int(1,90)
   maintenance_start_hour: int(0,23)

goodwe_controller/test_loop.py

@@ -0,0 +1,213 @@
+"""Runnable check for the control loop's cadence.  `python3 test_loop.py`
+
+SAFETY-12: the loop must evaluate on a clock as well as on a change. Before the
+fix, `run_control()` ran `cycle()` only when the meter value differed from the
+previous poll, so a meter that repeats a value ran NO control cycles while the
+heartbeat kept re-emitting the last command - measured on the rig during TEL-05
+as 70 s at a literally constant 350.0 W with 14 arrivals and zero cycles.
+
+⚠️ THIS TEST TAKES ~95 SECONDS OF WALL CLOCK (measured 93 s), on purpose, and
+that figure is the only thing standing between it and a future developer who
+decides a slow test is a broken one. The thing under test is a wall-clock floor
+inside a loop that sleeps 1 s; mocking the clock would leave the assertion
+testing the mock. It drives the real `run_control()` and counts what actually
+happened. Eight runs of the real loop is what the eight scenarios cost.
+
+⚠️ If you shorten the windows, re-measure and update this number and the one in
+HANDOVER.md. An understated runtime reads as a hang.
+
+`cycle_floor_s` is read from options with no lower bound in code, so a huge
+value reproduces the pre-fix behaviour exactly. Every claim below is therefore
+an A/B on one binary, not a comparison against a remembered old one.
+"""
+
+import asyncio
+import sys
+import time
+
+from app.main import Controller
+
+fails = []
+NEVER = 1e9          # cycle_floor_s so large the floor can never elapse: pre-fix
+
+
+def check(name, cond):
+    print(f"  {'ok  ' if cond else 'FAIL'} {name}")
+    if not cond:
+        fails.append(name)
+
+
+class FakeHass:
+    """A scripted meter and a plant that tracks the command instantly."""
+
+    def __init__(self, meter, soc_dies_at=None):
+        self.meter = meter
+        self.soc_dies_at = soc_dies_at
+        self.batt = 0.0
+        self.writes = []
+        self.t0 = time.monotonic()
+
+    async def limits(self, entity):
+        return (-5000.0, 5000.0, 1.0)
+
+    async def number(self, entity, invert=False):
+        now = time.monotonic() - self.t0
+        if entity == "sensor.grid":
+            return self.meter(now)
+        if entity == "sensor.batt":
+            return self.batt
+        if entity == "sensor.soc":
+            if self.soc_dies_at is not None and now >= self.soc_dies_at:
+                return None
+            return 50.0
+        return None
+
+    async def set_number(self, entity, value):
+        self.writes.append(float(value))
+        self.batt = float(value)
+        return True
+
+
+class _Store:
+    data = {}
+
+    def set(self, *a):
+        pass
+
+
+class _Pub:
+    enabled = False
+
+    def publish(self, *a, **k):
+        pass
+
+    def close(self):
+        pass
+
+
+BASE = {"setpoint_entity": "number.sp", "meter_entity": "sensor.grid",
+        "soc_entity": "sensor.soc", "batt_entity": "sensor.batt",
+        "meter_source": "off", "max_w": 2000, "gain": 0.6, "slew_w": 1000,
+        "deadband_w": 15, "target_grid_w": -10, "step_w": 10,
+        "heartbeat_s": 10, "stale_input_s": 15}
+
+
+def drive(meter, floor, seconds, soc_dies_at=None, **over):
+    """Run the real control loop for `seconds`; return (cycle times, writes)."""
+    async def go():
+        hass = FakeHass(meter, soc_dies_at)
+        c = Controller(dict(BASE, cycle_floor_s=floor, **over), hass, _Store(),
+                       _Pub(), stop=asyncio.Event())
+        c.auto = True
+        stamps = []
+        real = c.cycle
+
+        async def counted():
+            stamps.append(time.monotonic() - hass.t0)
+            await real()
+
+        c.cycle = counted
+        task = asyncio.create_task(c.run_control())
+        await asyncio.sleep(seconds)
+        c.stopping = True
+        await asyncio.wait_for(task, timeout=10)
+        return stamps, hass.writes, c.target, c.reason
+    return asyncio.run(go())
+
+
+def worst_gap(stamps, seconds):
+    """Longest stretch with no cycle, including the tail after the last one."""
+    edges = [0.0] + list(stamps) + [seconds]
+    return max(b - a for a, b in zip(edges, edges[1:]))
+
+
+# --------------------------------------------------------------------------- #
+print("a meter that repeats the same value")
+FLAT = lambda t: 350.0                                          # noqa: E731
+FLOOR, SECONDS = 3.0, 12.0
+
+pre_stamps, pre_writes, _, _ = drive(FLAT, NEVER, SECONDS)
+# The defect itself, demonstrated rather than described: one cycle at startup
+# and then nothing for the rest of the window, while writes keep happening.
+check("pre-fix: a constant meter runs exactly one cycle, at startup",
+      len(pre_stamps) == 1)
+check("...while the heartbeat keeps writing anyway, so nothing looks wrong",
+      len(pre_writes) >= 2)
+
+post_stamps, post_writes, _, _ = drive(FLAT, FLOOR, SECONDS)
+check("post-fix: the same constant meter runs cycles throughout",
+      len(post_stamps) >= int(SECONDS / FLOOR) - 1)
+# The actual acceptance criterion: a BOUND on the gap, not a count.
+gap = worst_gap(post_stamps, SECONDS)
+check(f"...with no gap longer than the floor ({gap:.1f}s <= {FLOOR + 1.5:.1f}s)",
+      gap <= FLOOR + 1.5)
+check("...and the loop actually corrected, instead of holding a stale command",
+      len(post_writes) > len(pre_writes))
+
+# --------------------------------------------------------------------------- #
+print("a meter that changes normally - nothing may move")
+# ⚠️ THE REGRESSION GUARD, and the more important half. The floor is a deadline
+# on the gap between cycles, reset by every cycle whichever trigger fired - not
+# a second scheduler. On a healthy meter it must never elapse, so the cycle
+# count, the write count and the commanded values must be IDENTICAL either side
+# of the fix. Anything else is a new write cadence, which SAFETY-12 forbids:
+# the deadband, step_w and the 10 s force-write decide what reaches the wire,
+# and this change is only allowed to alter when the loop thinks.
+STEPS = [0.0, 300.0, 850.0, -400.0, 120.0, -900.0, 60.0]
+LIVE = lambda t: STEPS[int(t // 2) % len(STEPS)]                # noqa: E731
+
+a_stamps, a_writes, _, _ = drive(LIVE, NEVER, 12.0)
+b_stamps, b_writes, _, _ = drive(LIVE, FLOOR, 12.0)
+check("a changing meter runs the same number of cycles as before the fix",
+      len(a_stamps) == len(b_stamps))
+check("...commanding exactly the same sequence of values", a_writes == b_writes)
+
+# --------------------------------------------------------------------------- #
+print("a meter parked at the target - the converged operating point")
+# The case TEL-05 warned about: at the converged target the power figure
+# legitimately repeats for minutes. The loop must still run, and must still
+# write nothing but the heartbeat, because the deadband - not the arrival
+# trigger - is what holds the command still.
+AT_TARGET = lambda t: -10.0                                     # noqa: E731
+c_stamps, c_writes, _, _ = drive(AT_TARGET, NEVER, 12.0)
+d_stamps, d_writes, _, _ = drive(AT_TARGET, FLOOR, 12.0)
+check("the loop evaluates at the converged point too", len(d_stamps) > len(c_stamps))
+check("...and the deadband still holds the command, so writes are unchanged",
+      d_writes == c_writes)
+
+# --------------------------------------------------------------------------- #
+print("an input dies while the meter repeats - the safety claim must still fire")
+# ⚠️ THE STRONGEST PROPERTY IN SAFETY-12, and the one that makes it a safety fix
+# rather than a latency fix. The `inputs missing -> 0 W` claim lives INSIDE
+# cycle() (main.py, the stale_input_s branch and the P_SAFETY claim below it).
+# Pre-fix, on a meter whose value happened to repeat, cycle() was never called
+# again - so that claim could not fire AT ALL. The controller held its last
+# command through an input outage of unbounded length with the status line still
+# reading "loop -> N W".
+#
+# Layer 1 does not cover this either on a `meter_source: off` install: no P1 age
+# sensor is published (see Controller.publish), so the firmware has nothing to
+# veto on, and the heartbeat keeps its watchdog fed the whole time.
+#
+# stale_input_s is shortened to 3 s here so the outage resolves inside a test
+# rather than inside a quarter of a minute. The mechanism is the default one.
+c2_stamps, c2_writes, pre_target, pre_reason = drive(
+    FLAT, NEVER, 10.0, soc_dies_at=4.0, stale_input_s=3)
+check("pre-fix: a dead input during a constant meter never reaches the safety claim",
+      pre_target != 0.0 and "safety" not in pre_reason)
+check(f"...so it holds its last command instead ({pre_target:g} W, {pre_reason!r})",
+      pre_target == 220.0)
+
+d2_stamps, d2_writes, post_target, post_reason = drive(
+    FLAT, FLOOR, 10.0, soc_dies_at=4.0, stale_input_s=3)
+check("post-fix: the same outage commands 0 W", post_target == 0.0)
+check(f"...through the safety claim, not by accident ({post_reason!r})",
+      "safety" in post_reason)
+check("...and the 0 W actually reached the device", 0.0 in d2_writes)
+
+# --------------------------------------------------------------------------- #
+print()
+if fails:
+    print(f"{len(fails)} FAILED: " + "; ".join(fails))
+    sys.exit(1)
+print("all checks passed")

goodwe_controller/test_p1.py

@@ -11,6 +11,7 @@ computes the wrong quarter-hour figure whenever the telegram cadence changes.
 """
 
 import asyncio
+import json
 import sys
 import time
 from datetime import datetime, timedelta, timezone
@@ -18,8 +19,11 @@ from datetime import datetime, timedelta, timezone
 import aiohttp   # already required by app.p1, so this adds no new dependency
 
 from app.p1 import (
-    P1Error, P1Ingest, HaDsmrSource, QuarterAverager, SOURCE_HA, SOURCE_MQTT,
-    make_sample, parse_mqtt_payload,
+    P1Error, P1Ingest, HaDsmrSource, HaSignedSource, HomeWizardLocalSource,
+    QuarterAverager,
+    SOURCE_HA, SOURCE_HA_SIGNED, SOURCE_HOMEWIZARD, SOURCE_MQTT,
+    build_source, is_enabled, make_sample, parse_homewizard, parse_mqtt_payload,
+    split_signed,
 )
 
 fails = []
@@ -56,6 +60,25 @@ def raises(name, fn):
     fails.append(name)
 
 
+def built(src):
+    """`src.build()`, with any escaping exception turned into a visible value.
+
+    ⚠️ Legibility of a RED, not leniency. build() is contracted to return a bool
+    and to funnel every bad telegram through ingest.reject() - a guard that goes
+    missing (say the "is the net entity cached at all" one) makes it raise
+    instead. That still fails the suite, but by aborting it with a traceback at
+    whichever check happened to run first, which costs the next person ten
+    minutes deciding whether the suite is broken or the code is. Returning the
+    exception makes it compare unequal to True/False, so the NAMED check goes red
+    and says which rule died.
+    """
+    try:
+        return src.build()
+    except Exception as err:  # noqa: BLE001 - a raise here is itself the failure
+        print(f"       build() raised {type(err).__name__}: {err}")
+        return err
+
+
 def sample(net_import, net_export=0.0, at=BASE, phases=1, pi=None, pe=None):
     return make_sample(SOURCE_HA, net_import, net_export, phases=phases,
                        phase_import_w=pi, phase_export_w=pe,
@@ -548,6 +571,726 @@ check("the averager integrated the live stream", live.averager.elapsed_s > 0.2)
 check("the primed cache let the first telegram build immediately",
       live.samples == 2 and live.last.import_w == 0.0)
 
+# --------------------------------------------------------------------------- #
+print("ha_signed: one signed entity -> the same two magnitudes")
+# The meter actually fitted at this house is a HomeWizard P1 publishing ONE
+# signed sensor. ha_dsmr cannot read it - it wants two unsigned registers and
+# refuses a negative one, which is every exporting telegram.
+
+check("a positive reading is import", split_signed(1500.0) == (1500.0, 0.0))
+check("a negative reading is export", split_signed(-900.0) == (0.0, 900.0))
+check("zero is a balanced reading, not a missing one",
+      split_signed(0.0) == (0.0, 0.0))
+check("exactly one magnitude is ever non-zero",
+      all(a == 0.0 or b == 0.0 for a, b in
+          (split_signed(v) for v in (-5710.0, -1.0, 0.0, 1.0, 4384.0))))
+# ⚠️ The split must not change the number. A control loop steered by a value
+# that was rounded or clamped on the way in is steered by a different meter.
+check("the split round-trips the signed value exactly",
+      all(make_sample(SOURCE_HA_SIGNED, *split_signed(v), phases=1).net_w == v
+          for v in (-11763.0, -5710.0, -0.5, 0.0, 0.5, 775.0, 4384.0)))
+
+raises("a non-numeric signed reading is rejected", lambda: split_signed("n/a"))
+raises("a signed None is rejected, not read as zero", lambda: split_signed(None))
+raises("a signed NaN is rejected", lambda: split_signed(float("nan")))
+raises("a signed infinity is rejected", lambda: split_signed(float("inf")))
+# ⚠️ This one matters MORE on the signed path than on the unsigned one. On
+# ha_dsmr the §20 contamination is also caught by "unsigned cannot be negative";
+# here 64954 arrives as a perfectly well-formed positive signed reading and the
+# plausibility ceiling is the only thing standing in front of it.
+raises("the 64954 signed-decode contamination is still rejected",
+       lambda: split_signed(64954.0))
+raises("...and its negative twin too", lambda: split_signed(-64954.0))
+
+# --------------------------------------------------------------------------- #
+print("ha_signed: the sign convention, against real captured readings")
+# ⚠️ Not a datasheet claim. These are literal values out of
+# sim/scenarios/ha-p1_meter_active_power-2026-08-{20,23}.json, HA recorder
+# exports of sensor.p1_meter_active_power at this house, copied here rather than
+# read from that repo so this file still runs on a laptop with nothing installed
+# (§17). If the convention were inverted, the physics below would be absurd.
+
+# 2026-08-23T11:46:52Z - the day's most negative reading, 13:46 local, full sun.
+s = make_sample(SOURCE_HA_SIGNED, *split_signed(-5710.0), phases=1)
+check("the midday PV peak (-5710 W) is EXPORT, not a 5.7 kW draw",
+      s.net_w == -5710.0 and s.export_w == 5710.0 and s.import_w == 0.0)
+# 2026-08-19T22:00:00Z - midnight local, 20 Aug's file starts here. No sun.
+s = make_sample(SOURCE_HA_SIGNED, *split_signed(775.0), phases=1)
+check("the overnight base load (+775 W) is IMPORT",
+      s.net_w == 775.0 and s.import_w == 775.0 and s.export_w == 0.0)
+# 2026-08-20T12:20:58Z - 14:20 local, the largest export in either capture.
+s = make_sample(SOURCE_HA_SIGNED, *split_signed(-11763.0), phases=1)
+check("the -11763 W midday extreme is export and survives the ceiling",
+      s.net_w == -11763.0 and s.export_w == 11763.0)
+# 2026-08-23T10:18:28Z - the largest import in the healthy capture.
+s = make_sample(SOURCE_HA_SIGNED, *split_signed(4384.0), phases=1)
+check("the +4384 W peak is import", s.net_w == 4384.0 and s.import_w == 4384.0)
+# The whole convention in one line: night draws, midday feeds back.
+check("night is positive and midday is negative, which is the convention",
+      split_signed(775.0)[0] > 0 and split_signed(-5710.0)[1] > 0)
+
+# --------------------------------------------------------------------------- #
+print("ha_signed transport: building a sample out of one entity state")
+
+NET = {"net": "sensor.p1_meter_active_power", "phase_net": []}
+ing = P1Ingest(phases=1, max_age_s=30.0)
+sig = HaSignedSource(None, ing, NET, token="x")
+
+check("nothing cached yet builds nothing", built(sig) is False and ing.last is None)
+sig._absorb("sensor.p1_meter_active_power", "1000")
+check("one signed entity is a complete telegram on its own",
+      built(sig) is True and ing.net_w == 1000.0)
+check("the sample is tagged with its own transport",
+      ing.last.source == SOURCE_HA_SIGNED)
+sig._absorb("sensor.p1_meter_active_power", "-2500")
+built(sig)
+check("a negative state lands as a negative net", ing.net_w == -2500.0)
+
+before = ing.last
+sig._absorb("sensor.p1_meter_active_power", "unavailable")
+check("an unavailable signed entity is a parse error", ing.parse_errors == 1)
+check("an unavailable entity does not build a sample", built(sig) is False)
+# ⚠️ The rule the whole ticket turns on: a missing reading is MISSING. Resolving
+# it to 0 W would read as a perfectly balanced house and defeat the staleness
+# trigger that FW-01's watchdog is built on.
+check("an unavailable entity leaves the last good sample untouched, not 0 W",
+      ing.last is before and ing.net_w == -2500.0)
+sig._absorb("sensor.p1_meter_active_power", "unknown")
+check("an unknown signed entity is treated the same way", ing.parse_errors == 2)
+sig._absorb("sensor.p1_meter_active_power", "banana")
+check("a non-numeric signed state is a parse error, not 0 W",
+      ing.parse_errors == 3 and ing.net_w == -2500.0)
+sig._absorb("sensor.p1_meter_active_power", "64954")
+check("64954 is refused at the signed transport too",
+      built(sig) is False and ing.parse_errors == 4)
+sig._absorb("sensor.not_ours", "123")
+check("an unsubscribed entity is never cached by the signed transport",
+      "sensor.not_ours" not in sig.cache)
+
+# A rejected reading must not make the age look fresh - the age is what the
+# firmware watchdog reads, and a rejection is exactly when it must keep climbing.
+ing = P1Ingest(phases=1, max_age_s=30.0)
+sig = HaSignedSource(None, ing, dict(NET), token="x")
+ing.submit(make_sample(SOURCE_HA_SIGNED, 1200, 0, phases=1,
+                       ingest_mono=time.monotonic() - 20.0))
+sig._absorb("sensor.p1_meter_active_power", "unavailable")
+built(sig)
+check("a rejected reading does not reset the published age",
+      ing.published_age_s > 19 and ing.net_w == 1200.0)
+ing.submit(make_sample(SOURCE_HA_SIGNED, 1200, 0, phases=1,
+                       ingest_mono=time.monotonic() - 40.0))
+check("...and the age keeps climbing past max_age_s on its own",
+      ing.stale is True and ing.net_w is None)
+
+# The three-phase reading the TEL-04 survey recorded at this house: L1 +2301 W,
+# L2 +468 W, L3 -2582 W, netting +187 W. A signed per-phase set splits the same
+# way, and the exporting phase must still clamp out of the billed figure.
+ing3 = P1Ingest(phases=3, max_age_s=30.0)
+NET3 = {"net": "sensor.p1_meter_active_power",
+        "phase_net": ["sensor.p1_l1", "sensor.p1_l2", "sensor.p1_l3"]}
+sig3 = HaSignedSource(None, ing3, NET3, token="x")
+for eid, val in (("sensor.p1_meter_active_power", "187"), ("sensor.p1_l1", "2301")):
+    sig3._absorb(eid, val)
+check("an incomplete signed phase set waits instead of guessing", built(sig3) is False)
+sig3._absorb("sensor.p1_l2", "468")
+sig3._absorb("sensor.p1_l3", "-2582")
+check("a complete signed three-phase set builds", built(sig3) is True)
+check("signed per-phase entities keep the exporting phase negative",
+      ing3.last.per_phase_w == (2301.0, 468.0, -2582.0))
+check("per-phase IMPORT clamps the exporting phase to zero",
+      ing3.last.per_phase_import_w == (2301.0, 468.0, 0.0))
+check("the phase import sum is 2769 W while the connection nets 187 W",
+      sum(ing3.last.per_phase_import_w) == 2769.0 and ing3.last.net_w == 187.0)
+check("the signed per-phase tuple length matches meter_phases",
+      len(ing3.last.per_phase_w) == ing3.phases == 3)
+
+sig_bad = HaSignedSource(None, P1Ingest(phases=3, max_age_s=30.0),
+                         {"net": "sensor.net", "phase_net": ["sensor.a", "sensor.b"]},
+                         token="x")
+for eid in ("sensor.net", "sensor.a", "sensor.b"):
+    sig_bad._absorb(eid, "100")
+check("two phases delivered against meter_phases 3 is rejected, not padded",
+      built(sig_bad) is False and sig_bad.ingest.last is None
+      and sig_bad.ingest.parse_errors == 1)
+
+# --------------------------------------------------------------------------- #
+print("ha_signed transport: end to end against a fake Home Assistant")
+# The transport is a subclass, so this is what proves the INHERITED machinery -
+# auth, subscribe, the get_states priming rule, the reconnect-emits-nothing
+# rule - still behaves when only _wanted() and build() were replaced.
+
+
+async def _e2e_signed():
+    from aiohttp import web
+    import app.p1 as p1mod
+
+    done = asyncio.Event()
+    eid = "sensor.p1_meter_active_power"
+
+    async def fake_ha(request):
+        ws = web.WebSocketResponse()
+        await ws.prepare(request)
+        await ws.send_json({"type": "auth_required", "ha_version": "2026.8"})
+        auth = await ws.receive_json()
+        assert auth["type"] == "auth" and auth["access_token"] == "tok"
+        await ws.send_json({"type": "auth_ok"})
+        sub = await ws.receive_json()
+        assert sub["type"] == "subscribe_events"
+        await ws.send_json({"id": sub["id"], "type": "result", "success": True})
+        get = await ws.receive_json()
+        assert get["type"] == "get_states"
+        await ws.send_json({"id": get["id"], "type": "result", "success": True, "result": [
+            {"entity_id": eid, "state": "775.0"},
+            {"entity_id": "sensor.something_else", "state": "hello"},
+        ]})
+        # Two real telegrams, both literal captured values: overnight import,
+        # then the midday export peak.
+        for val in ("775.0", "-5710.0"):
+            await asyncio.sleep(0.5)
+            await ws.send_json({"type": "event", "event": {"data": {
+                "entity_id": eid,
+                "new_state": {"entity_id": eid, "state": val}}}})
+        await asyncio.sleep(0.5)
+        await ws.send_json({"type": "event", "event": {"data": {
+            "entity_id": eid,
+            "new_state": {"entity_id": eid, "state": "unavailable"}}}})
+        await asyncio.sleep(0.5)
+        done.set()
+        return ws
+
+    srv = web.Application()
+    srv.router.add_get("/ws", fake_ha)
+    runner = web.AppRunner(srv)
+    await runner.setup()
+    site = web.TCPSite(runner, "127.0.0.1", 0)
+    await site.start()
+    port = site._server.sockets[0].getsockname()[1]
+    p1mod.WS_URL = f"http://127.0.0.1:{port}/ws"
+
+    ing = P1Ingest(phases=1, max_age_s=30.0)
+    async with aiohttp.ClientSession() as sess:
+        src = HaSignedSource(sess, ing, dict(NET), token="tok")
+        task = asyncio.get_running_loop().create_task(src.run())
+        try:
+            await asyncio.wait_for(done.wait(), 20)
+            await asyncio.sleep(0.5)
+        finally:
+            task.cancel()
+            try:
+                await task
+            except asyncio.CancelledError:
+                pass
+    await runner.cleanup()
+    return ing, src
+
+
+live, wire = asyncio.run(_e2e_signed())
+# ⚠️ TWO, not three - the same rule as the ha_dsmr e2e. get_states primes the
+# cache but must never become a sample: after a Core restart it is a
+# RestoreEntity value of unknown age, and stamping it with ingest_ts=now reports
+# a fresh meter that may have been dead for an hour.
+check("ha_signed does not manufacture a sample from cached HA state",
+      live.samples == 2)
+check("the signed telegrams arrived over a real websocket",
+      live.last.source == SOURCE_HA_SIGNED)
+check("the final export telegram nets negative, over the wire",
+      live.last.net_w == -5710.0 and live.last.export_w == 5710.0)
+check("ha_signed subscribes to the one entity and caches nothing else",
+      wire.ids == {"sensor.p1_meter_active_power"}
+      and "sensor.something_else" not in wire.cache)
+check("a mid-stream unavailable signed state is a parse error, not a sample",
+      live.parse_errors == 1 and live.samples == 2)
+# ⚠️ And the cached half is DROPPED, so no later telegram can be assembled out
+# of a value that stopped reporting.
+check("an unavailable entity is evicted from the cache", wire.cache == {})
+check("the last good reading survives the unavailable, and is not 0 W",
+      live.net_w == -5710.0)
+check("the averager integrated the live signed stream", live.averager.elapsed_s > 0.2)
+# ⚠️ The entity FW-01 waits on. It must be a number here exactly as it is on the
+# other transports - the house P1 went 51.1 s and 36.2 s between state changes
+# overnight, and without this the watchdog false-trips the battery to 0 W.
+check("sensor.p1_sample_age_s is a live number on this transport too",
+      isinstance(live.published_age_s, float) and live.published_age_s >= 0.0)
+
+# --------------------------------------------------------------------------- #
+print("ha_signed: selection by config")
+
+check("ha_signed is enabled", is_enabled({"meter_source": SOURCE_HA_SIGNED}) is True)
+# ⚠️ `sel`, not `built` - that name is the build() wrapper defined at the top of
+# this file, and rebinding it here silently disarms every check appended below
+# this line. Caught in review: an added check went `TypeError: 'HaSignedSource'
+# object is not callable` and aborted the suite, which is the exact failure the
+# wrapper exists to prevent, reintroduced by a name collision.
+sel = build_source({"meter_source": SOURCE_HA_SIGNED,
+                    "p1_net_entity": "sensor.p1_meter_active_power"},
+                   P1Ingest(), None, None)
+check("meter_source ha_signed selects the signed transport",
+      isinstance(sel, HaSignedSource))
+check("...wired to p1_net_entity, and subscribed to exactly that one entity",
+      sel.ids == {"sensor.p1_meter_active_power"})
+# ⚠️ The three modes must not bleed into each other: ha_dsmr must keep ignoring
+# p1_net_entity, or a half-configured install silently reads the wrong sensor.
+plain = build_source({"meter_source": SOURCE_HA,
+                      "p1_import_entity": "sensor.i", "p1_export_entity": "sensor.e",
+                      "p1_net_entity": "sensor.p1_meter_active_power"},
+                     P1Ingest(), None, None)
+check("ha_dsmr still selects the unsigned transport and ignores p1_net_entity",
+      type(plain) is HaDsmrSource and plain.ids == {"sensor.i", "sensor.e"})
+check("meter_source off still selects nothing",
+      build_source({"meter_source": "off"}, P1Ingest(), None, None) is None)
+check("an unrecognised meter_source selects nothing rather than guessing",
+      build_source({"meter_source": "ha_signd"}, P1Ingest(), None, None) is None)
+
+# ⚠️ Caught once at startup, not once per telegram. A source that is wired up
+# wrong otherwise fails in the one way indistinguishable from a healthy source
+# nobody has sent anything to yet: no samples, a climbing age, the watchdog
+# holding the battery at 0 W, and nothing in the log saying why.
+check("a blank p1_net_entity is refused rather than silently never receiving",
+      build_source({"meter_source": SOURCE_HA_SIGNED, "p1_net_entity": ""},
+                   P1Ingest(), None, None) is None)
+check("...and whitespace does not sneak past it",
+      build_source({"meter_source": SOURCE_HA_SIGNED, "p1_net_entity": "   "},
+                   P1Ingest(), None, None) is None)
+check("a phase list that disagrees with meter_phases is refused at startup",
+      build_source({"meter_source": SOURCE_HA_SIGNED, "p1_net_entity": "sensor.n",
+                    "p1_phase_net_entities": ["sensor.a", "sensor.b"]},
+                   P1Ingest(phases=3), None, None) is None)
+check("a phase list that agrees with meter_phases is accepted",
+      isinstance(build_source(
+          {"meter_source": SOURCE_HA_SIGNED, "p1_net_entity": "sensor.n",
+           "p1_phase_net_entities": ["sensor.a", "sensor.b", "sensor.c"]},
+          P1Ingest(phases=3), None, None), HaSignedSource))
+check("no phase list at all is still fine - per-phase billing is optional",
+      isinstance(build_source(
+          {"meter_source": SOURCE_HA_SIGNED, "p1_net_entity": "sensor.n"},
+          P1Ingest(phases=3), None, None), HaSignedSource))
+
+# --------------------------------------------------------------------------- #
+print("homewizard_local: parsing the meter's own /api/v1/data document")
+# The same JSON `sim/hwsim.py` serves and the same JSON the real meter at
+# 192.168.2.250 serves. One SIGNED connection figure plus three signed legs, so
+# it goes through the same split_signed as ha_signed - the sign convention is
+# not re-derived on this transport, it is reused.
+
+
+def hw_doc(w, l1=None, l2=None, l3=None, imp_kwh=1234.567, exp_kwh=890.123):
+    return {"wifi_ssid": "sim", "smr_version": 50, "meter_model": "SIM-P1",
+            "total_power_import_kwh": imp_kwh, "total_power_export_kwh": exp_kwh,
+            "active_power_w": w,
+            "active_power_l1_w": l1, "active_power_l2_w": l2,
+            "active_power_l3_w": l3, "total_gas_m3": 0.0}
+
+
+s = parse_homewizard(hw_doc(775.0, l1=775.0), 1)
+check("the overnight base load (+775 W) is import on this transport too",
+      s.net_w == 775.0 and s.import_w == 775.0 and s.export_w == 0.0)
+check("the sample is tagged homewizard_local", s.source == SOURCE_HOMEWIZARD)
+s = parse_homewizard(hw_doc(-5710.0, l1=-5710.0), 1)
+check("the midday PV peak (-5710 W) is export, not a 5.7 kW draw",
+      s.net_w == -5710.0 and s.export_w == 5710.0)
+check("a single-phase document still yields its one leg", s.per_phase_w == (-5710.0,))
+
+# The TEL-04 three-phase survey reading, served the HomeWizard way.
+s = parse_homewizard(hw_doc(187.0, 2301.0, 468.0, -2582.0), 3)
+check("signed legs keep the exporting phase negative",
+      s.per_phase_w == (2301.0, 468.0, -2582.0))
+check("per-phase import clamps the exporting leg out of the billed figure",
+      s.per_phase_import_w == (2301.0, 468.0, 0.0))
+check("the legs sum to 2769 W while the connection nets 187 W",
+      sum(s.per_phase_import_w) == 2769.0 and s.net_w == 187.0)
+
+# ⚠️ A single-phase HomeWizard serves `active_power_l2_w: null`. Unlike the HA
+# transports there is no "wait for the rest" case - every field came out of ONE
+# response, so a missing leg cannot be a STALE leg. Dropping the whole sample
+# over it would turn a healthy meter into a climbing age, which is the exact
+# false trip this transport exists to remove.
+def parsed(doc, phases=1):
+    """parse_homewizard(), with an escaping exception turned into a visible value.
+
+    Same reason as `built()` above: if the "all legs or none" guard goes missing,
+    parsing raises, and without this the suite aborts on a traceback instead of
+    reddening the NAMED check that says which rule died.
+    """
+    try:
+        return parse_homewizard(doc, phases)
+    except Exception as err:  # noqa: BLE001 - a raise here is itself the failure
+        print(f"       parse_homewizard raised {type(err).__name__}: {err}")
+        return err
+
+
+s = parsed(hw_doc(500.0, l1=500.0), 3)
+check("a meter serving fewer legs than meter_phases still gives a reading",
+      getattr(s, "net_w", None) == 500.0 and getattr(s, "per_phase_w", "?") is None)
+check("...and does not fabricate a partial phase tuple",
+      getattr(s, "per_phase_import_w", "?") is None)
+
+raises("a response that is not a JSON object is rejected",
+       lambda: parse_homewizard([1, 2, 3], 1))
+raises("a document with no active_power_w is rejected, not read as 0 W",
+       lambda: parse_homewizard({"total_gas_m3": 0.0}, 1))
+raises("a null active_power_w is rejected", lambda: parse_homewizard(hw_doc(None), 1))
+raises("a string active_power_w is rejected", lambda: parse_homewizard(hw_doc("775"), 1))
+raises("a NaN active_power_w is rejected",
+       lambda: parse_homewizard(hw_doc(float("nan")), 1))
+raises("the 64954 signed-decode contamination is refused here too",
+       lambda: parse_homewizard(hw_doc(64954.0), 1))
+raises("a non-numeric leg is rejected rather than quietly dropped",
+       lambda: parse_homewizard(hw_doc(600.0, "2000", 0.0, 100.0), 3))
+
+# --------------------------------------------------------------------------- #
+print("homewizard_local: every HTTP response is an arrival")
+# THE WHOLE TICKET. sensor.p1_sample_age_s has to mean "time since the meter
+# REPORTED", not "time since the value CHANGED". Home Assistant cannot express
+# the first: a repeated reading emits no state_changed, advances last_reported
+# on neither serialiser, and state_reported cannot be subscribed to at all
+# ("Event filter is required"). Measured on the ENV-01 rig over 70 s of a frozen
+# meter and again against the live house over ten repeated readings. Our own
+# capture of this house's meter goes 42.2 s and 97.0 s between changes, both past
+# the default meter_max_age_s of 30 - i.e. the age sensor would command 0 W on a
+# perfectly healthy meter. Polling the meter itself removes that: the response is
+# the arrival, and the number in it is not consulted.
+
+
+class _FakeMeter:
+    """hwsim in eight lines: serves whatever document it is told to, or a fault."""
+
+    def __init__(self, doc=None):
+        self.doc = doc
+        self.status = 200
+        self.body = None          # set to raw text to serve something unparseable
+        self.delay = 0.0          # set to seconds to imitate a meter that hangs
+        self.hits = 0
+
+    async def handle(self, request):
+        from aiohttp import web
+        self.hits += 1
+        if self.delay:
+            await asyncio.sleep(self.delay)
+        # ⚠️ web.Response(text=...) defaults to text/plain. That is not just the
+        # "unparseable body" path: fed VALID json it serves a good document under
+        # the wrong mimetype, which is the only way to reach the content_type
+        # guard in poll_once - json_response can never produce it.
+        if self.body is not None:
+            return web.Response(text=self.body, status=self.status)
+        return web.json_response(self.doc, status=self.status)
+
+
+async def _hw_rig(fn):
+    """Run `fn(make_source, meter)` against a real HTTP server on localhost."""
+    from aiohttp import web
+    meter = _FakeMeter(hw_doc(350.0, l1=350.0))
+    app = web.Application()
+    app.router.add_get("/api/v1/data", meter.handle)
+    runner = web.AppRunner(app)
+    await runner.setup()
+    site = web.TCPSite(runner, "127.0.0.1", 0)
+    await site.start()
+    port = site._server.sockets[0].getsockname()[1]
+    async with aiohttp.ClientSession() as sess:
+        try:
+            return await fn(sess, port, meter)
+        finally:
+            await runner.cleanup()
+
+
+async def _arrivals(sess, port, meter):
+    ing = P1Ingest(phases=1, max_age_s=30.0)
+    src = HomeWizardLocalSource(sess, ing, "127.0.0.1", port=port, poll_s=1.0)
+    out = {}
+    out["first"] = await src.poll_once()
+    out["stamp1"] = ing.last.ingest_mono
+    # Four more polls of the IDENTICAL document - the meter has not moved a watt.
+    for _ in range(4):
+        await asyncio.sleep(0.05)
+        await src.poll_once()
+    out["ing"], out["src"], out["meter"] = ing, src, meter
+    return out
+
+
+r = asyncio.run(_hw_rig(_arrivals))
+ing, src = r["ing"], r["src"]
+check("a poll of the meter's own API builds a sample",
+      r["first"] is True and ing.net_w == 350.0)
+# ⚠️ THE acceptance criterion. Five identical readings, five arrivals. On
+# ha_signed this whole sequence produces exactly ONE state_changed and then
+# silence, and the age climbs to 30 s on a meter that is answering perfectly.
+check("five identical readings are five arrivals, not one",
+      ing.samples == 5 and r["meter"].hits == 5 and src.polls == 5)
+check("an unchanged value still stamps a NEW arrival time",
+      ing.last.ingest_mono > r["stamp1"])
+check("...so the age resets on a response carrying an unchanged number",
+      ing.published_age_s < 1.0 and ing.stale is False)
+check("no arrival was ever a parse error", ing.parse_errors == 0)
+
+# --------------------------------------------------------------------------- #
+print("homewizard_local: frozen vs steady, the pair HA cannot separate")
+# ⚠️ Read this before changing anything here. A frozen meter (hwsim --fault
+# freeze) answers 200 OK forever with a stale document. It is ARRIVING. So the
+# age - an arrival detector, correctly - reads fresh on both, and that is not a
+# defect in the age, it is the definition of the signal. What the local API adds
+# that Home Assistant never had is the ENERGY REGISTERS: a meter under real load
+# advances total_power_import_kwh (1 Wh resolution, ~10 s at 350 W) even when the
+# power figure repeats, and a frozen one does not. That is the discriminator, and
+# it is exposed as `unchanged_s` - deliberately NOT folded into the age, because
+# this controller regulates grid power toward ~0 W and at a converged -10 W the
+# export register needs six minutes to move. Thresholding unchanged_s at 30 s
+# would rebuild the false-trip limit cycle at the exact operating point we aim
+# for. See DOCS.md and HomeWizardLocalSource.unchanged_s.
+
+
+async def _freeze_vs_steady(sess, port, meter):
+    ing_f = P1Ingest(phases=1, max_age_s=30.0)
+    frozen = HomeWizardLocalSource(sess, ing_f, "127.0.0.1", port=port, poll_s=1.0)
+    meter.doc = hw_doc(350.0, l1=350.0)          # --fault freeze: never moves
+    for i in range(4):
+        if i:
+            await asyncio.sleep(0.1)             # sleep BEFORE, so unchanged_s
+        await frozen.poll_once()                 # is read the instant a poll lands
+
+    ing_s = P1Ingest(phases=1, max_age_s=30.0)
+    steady = HomeWizardLocalSource(sess, ing_s, "127.0.0.1", port=port, poll_s=1.0)
+    kwh = 1234.567
+    for i in range(4):
+        if i:
+            await asyncio.sleep(0.1)
+        # A steady 350 W house: the power figure repeats, the register climbs.
+        kwh += 0.001
+        meter.doc = hw_doc(350.0, l1=350.0, imp_kwh=round(kwh, 3))
+        await steady.poll_once()
+    return (ing_f, frozen), (ing_s, steady)
+
+
+(ing_f, frozen), (ing_s, steady) = asyncio.run(_hw_rig(_freeze_vs_steady))
+check("a frozen meter keeps arriving, so both read the same power",
+      ing_f.net_w == 350.0 and ing_s.net_w == 350.0)
+# ⚠️ Recorded as a rule, not a shortcoming: the age is an ARRIVAL detector and a
+# frozen meter genuinely is arriving. Anyone tempted to make the age catch freeze
+# is about to reintroduce the false trip on a steady house.
+check("the age cannot separate them, and is fresh on both",
+      ing_f.published_age_s < 1.0 and ing_s.published_age_s < 1.0)
+check("the frozen meter's measurement stands still", frozen.unchanged_s > 0.25)
+check("...while the steady meter's energy register keeps advancing",
+      steady.unchanged_s < 0.05)
+check("so the two ARE separable on the local API, which HA could not do",
+      frozen.unchanged_s > steady.unchanged_s * 3)
+check("unchanged_s is None before the first response ever lands",
+      HomeWizardLocalSource(None, P1Ingest(), "h").unchanged_s is None)
+
+# --------------------------------------------------------------------------- #
+print("homewizard_local: a failed poll is a missing reading, never 0 W")
+
+
+async def _failures(sess, port, meter):
+    ing = P1Ingest(phases=1, max_age_s=30.0)
+    src = HomeWizardLocalSource(sess, ing, "127.0.0.1", port=port, poll_s=1.0)
+    await src.poll_once()
+    # Age the good sample by hand so a reset would be unmistakable.
+    ing.submit(make_sample(SOURCE_HOMEWIZARD, 350.0, 0.0, phases=1,
+                           ingest_mono=time.monotonic() - 90.0))
+    out = {}
+    meter.status = 500
+    out["http500"] = await src.poll_once()
+    out["conn_after_500"] = src.connected
+    meter.status, meter.body = 200, "<html>gateway</html>"
+    out["notjson"] = await src.poll_once()
+    meter.body = None
+    meter.doc = {"total_gas_m3": 0.0}            # 200 OK, no power in it
+    out["nopower"] = await src.poll_once()
+    out["ing"], out["src"] = ing, src
+
+    # And a meter that is not listening at all: `--fault down`.
+    dead = HomeWizardLocalSource(sess, P1Ingest(phases=1, max_age_s=30.0),
+                                 "127.0.0.1", port=1, poll_s=1.0)
+    out["down"] = await dead.poll_once()
+    out["dead"] = dead
+    return out
+
+
+r = asyncio.run(_hw_rig(_failures))
+ing, src = r["ing"], r["src"]
+check("an HTTP 500 is not a reading", r["http500"] is False)
+# A source that was connected and then failed must SAY it is disconnected -
+# otherwise the diagnostic reads healthy while the age climbs, which is exactly
+# the "connected: True, parse_errors: 0, samples: 0" state the rig recorded.
+check("a poll that fails clears the connected flag", r["conn_after_500"] is False)
+check("a 200 OK carrying something that is not JSON is not a reading",
+      r["notjson"] is False)
+check("a 200 OK with no active_power_w in it is not a reading", r["nopower"] is False)
+check("a meter that refuses the connection is not a reading",
+      r["down"] is False and r["dead"].connected is False)
+check("every failure was counted as a parse error", ing.parse_errors == 3)
+check("...and the transport records the transport-level ones separately",
+      src.poll_errors == 2 and src.polls == 4)
+# ⚠️ The rule the safety chain rests on. A failed poll must not manufacture a
+# balanced house, and must not reset the clock the watchdog reads.
+check("a failed poll does not reset the age", ing.published_age_s > 89)
+check("a failed poll leaves the last good value in place, and it is not 0 W",
+      ing.last.net_w == 350.0 and ing.stale is True and ing.net_w is None)
+check("no failed poll ever became a sample", ing.samples == 2)
+check("a 200 OK marks the transport connected even when its body is refused",
+      src.connected is True)
+
+# --------------------------------------------------------------------------- #
+print("homewizard_local: a wrong header, a hung meter, a submit that throws")
+# Three failure shapes that all end the same way if they are mishandled - no
+# sample, a climbing age, the battery at 0 W - and each of which would send the
+# operator hunting the wrong device.
+
+
+async def _header_and_timeout(sess, port, meter):
+    out = {}
+    # Valid JSON under text/plain: exactly what content_type=None is for.
+    meter.body = json.dumps(hw_doc(350.0, l1=350.0))
+    ing = P1Ingest(phases=1, max_age_s=30.0)
+    src = HomeWizardLocalSource(sess, ing, "127.0.0.1", port=port, poll_s=1.0)
+    out["mimetype"] = await src.poll_once()
+    out["ing"] = ing
+    meter.body = None
+
+    # A meter that takes the connection and then does not answer.
+    meter.delay = 0.6
+    ing_t = P1Ingest(phases=1, max_age_s=30.0)
+    slow = HomeWizardLocalSource(sess, ing_t, "127.0.0.1", port=port,
+                                 poll_s=1.0, timeout_s=0.05)
+    out["timeout"] = await slow.poll_once()
+    out["timeout_err"] = ing_t.last_error
+    meter.delay = 0.0
+    return out
+
+
+r = asyncio.run(_hw_rig(_header_and_timeout))
+# ⚠️ A real firmware answering text/plain must not read as a dead meter. Drop
+# content_type=None from poll_once and this goes red with "unexpected mimetype".
+check("valid JSON under the wrong Content-Type is still a reading",
+      r["mimetype"] is True and r["ing"].samples == 1 and r["ing"].net_w == 350.0)
+# ⚠️ str(asyncio.TimeoutError()) is the EMPTY STRING. Without the class-name
+# fallback the status page reads "last error:" and then nothing, on a hung
+# meter, at the moment someone is reading that line to find out why the battery
+# went to 0 W.
+check("a timed-out poll names the fault instead of logging an empty reason",
+      r["timeout"] is False and "TimeoutError" in (r["timeout_err"] or ""))
+
+
+async def _submit_rejects(sess, port, meter):
+    """submit() raising P1Error must be a rejection, not an escaping exception."""
+    class _P1Boom(P1Ingest):
+        def submit(self, sample):
+            raise P1Error("register went backwards")
+
+    ing = _P1Boom(phases=1, max_age_s=30.0)
+    src = HomeWizardLocalSource(sess, ing, "127.0.0.1", port=port, poll_s=1.0)
+    try:
+        ok = await src.poll_once()
+    except Exception as err:      # noqa: BLE001 - an escape IS the failure
+        ok = err
+    return ok, ing.parse_errors
+
+
+ok, errs = asyncio.run(_hw_rig(_submit_rejects))
+check("a submit that rejects the sample is handled, not left to escape",
+      ok is False and errs == 1)
+
+
+async def _submit_explodes(sess, port, meter):
+    """And an UNEXPECTED raise must not kill the poll task for good."""
+    class _Boom(P1Ingest):
+        def submit(self, sample):
+            raise RuntimeError("kaboom")
+
+    src = HomeWizardLocalSource(sess, _Boom(phases=1, max_age_s=30.0),
+                                "127.0.0.1", port=port, poll_s=0.05)
+    task = asyncio.create_task(src.run())
+    await asyncio.sleep(0.3)
+    alive = not task.done()
+    task.cancel()
+    # ⚠️ BaseException, and the same reason built() exists: if run() loses its
+    # guard the task is already dead HOLDING the RuntimeError, and awaiting it
+    # re-raises - aborting the whole suite with a traceback instead of reddening
+    # the check that names the rule. The death is what `alive` records; catching
+    # it here is bookkeeping, not leniency.
+    try:
+        await task
+    except BaseException:  # noqa: BLE001
+        pass
+    return alive, src.polls
+
+
+# ⚠️ The silent-death case. A dead poll task fails SAFE - the age climbs and the
+# controller commands 0 W - but it looks exactly like a dead meter, so the
+# operator spends the outage power-cycling hardware that was never at fault.
+alive, polls = asyncio.run(_hw_rig(_submit_explodes))
+check("a raise inside a poll does not permanently kill the polling task",
+      alive is True and polls > 1)
+
+# --------------------------------------------------------------------------- #
+print("homewizard_local: selection by config")
+
+check("homewizard_local is enabled", is_enabled({"meter_source": SOURCE_HOMEWIZARD}) is True)
+sel = build_source({"meter_source": SOURCE_HOMEWIZARD, "p1_host": "192.168.2.250"},
+                   P1Ingest(), None, None)
+check("meter_source homewizard_local selects the polling transport",
+      isinstance(sel, HomeWizardLocalSource))
+# ⚠️ getattr, not attribute access, for the same reason `built()` exists: a
+# startup guard that goes wrong returns None here, and `None.url` would abort the
+# suite with a traceback instead of reddening the check that names the rule.
+check("...pointed at the meter's own local API on the default port",
+      getattr(sel, "url", None) == "http://192.168.2.250:80/api/v1/data")
+check("the default cadence is the meter's own ~5 s update rate",
+      getattr(sel, "poll_s", None) == 5.0)
+# ⚠️ The request must not outlive the poll interval: a backlog of queued requests
+# behind a slow meter would land several arrivals for one measurement.
+check("the request timeout is held under the poll interval",
+      getattr(sel, "timeout_s", 99) < getattr(sel, "poll_s", 0))
+
+sel = build_source({"meter_source": SOURCE_HOMEWIZARD, "p1_host": "10.0.0.9:8080"},
+                   P1Ingest(), None, None)
+check("an explicit host:port is honoured, which is how the sim is reached",
+      getattr(sel, "url", None) == "http://10.0.0.9:8080/api/v1/data")
+sel = build_source({"meter_source": SOURCE_HOMEWIZARD,
+                    "p1_host": "http://192.168.2.250/"}, P1Ingest(), None, None)
+check("a pasted browser URL still resolves to the right host",
+      getattr(sel, "url", None) == "http://192.168.2.250:80/api/v1/data")
+
+# ⚠️ Caught once at startup, not once per poll - a source wired up wrong
+# otherwise fails in the one way indistinguishable from a healthy one nobody has
+# polled yet: no samples, a climbing age, the watchdog at 0 W, nothing in the log.
+check("a blank p1_host is refused rather than silently never polling",
+      build_source({"meter_source": SOURCE_HOMEWIZARD, "p1_host": ""},
+                   P1Ingest(), None, None) is None)
+check("...and whitespace does not sneak past it",
+      build_source({"meter_source": SOURCE_HOMEWIZARD, "p1_host": "   "},
+                   P1Ingest(), None, None) is None)
+check("an unparseable port is refused rather than guessed",
+      build_source({"meter_source": SOURCE_HOMEWIZARD, "p1_host": "meter:eighty"},
+                   P1Ingest(), None, None) is None)
+# ⚠️ The age can never be fresher than the poll interval, so a cadence at or past
+# max_age_s means every reading is stale before its successor arrives: the
+# controller would sit permanently on missing inputs while the meter is fine.
+check("a poll cadence at meter_max_age_s is refused",
+      build_source({"meter_source": SOURCE_HOMEWIZARD, "p1_host": "m",
+                    "meter_poll_s": 30}, P1Ingest(max_age_s=30), None, None) is None)
+check("...and one past it too",
+      build_source({"meter_source": SOURCE_HOMEWIZARD, "p1_host": "m",
+                    "meter_poll_s": 45}, P1Ingest(max_age_s=30), None, None) is None)
+check("a cadence with headroom is accepted",
+      isinstance(build_source({"meter_source": SOURCE_HOMEWIZARD, "p1_host": "m",
+                               "meter_poll_s": 5}, P1Ingest(max_age_s=30),
+                              None, None), HomeWizardLocalSource))
+check("a zero cadence is refused rather than spinning",
+      build_source({"meter_source": SOURCE_HOMEWIZARD, "p1_host": "m",
+                    "meter_poll_s": 0}, P1Ingest(max_age_s=30), None, None) is None)
+check("a non-numeric cadence is refused",
+      build_source({"meter_source": SOURCE_HOMEWIZARD, "p1_host": "m",
+                    "meter_poll_s": "fast"}, P1Ingest(max_age_s=30), None, None) is None)
+# The four modes must not bleed into each other.
+check("ha_signed ignores p1_host and still selects the entity transport",
+      type(build_source({"meter_source": SOURCE_HA_SIGNED, "p1_net_entity": "sensor.n",
+                         "p1_host": "192.168.2.250"}, P1Ingest(), None, None))
+      is HaSignedSource)
+check("homewizard_local ignores p1_net_entity and needs its own host",
+      build_source({"meter_source": SOURCE_HOMEWIZARD,
+                    "p1_net_entity": "sensor.n"}, P1Ingest(), None, None) is None)
+
 # --------------------------------------------------------------------------- #
 print("the age sensor must not exist when P1 is off")
 # ⚠️ This is a fleet-wide regression guard, not a nicety. The ESP32 watchdog
@@ -556,7 +1299,6 @@ print("the age sensor must not exist when P1 is off")
 # age were published with meter_source off it would climb past 30 s on every
 # existing install within half a minute and pin the inverter at 0 W forever.
 
-from app.p1 import is_enabled          # noqa: E402
 from app.mqtt import SENSORS, MqttPublisher   # noqa: E402
 
 check("meter_source off is disabled", is_enabled({"meter_source": "off"}) is False)
@@ -564,6 +1306,8 @@ check("a missing meter_source is disabled", is_enabled({}) is False)
 check("an empty meter_source is disabled", is_enabled({"meter_source": ""}) is False)
 check("ha_dsmr is enabled", is_enabled({"meter_source": SOURCE_HA}) is True)
 check("mqtt_p1 is enabled", is_enabled({"meter_source": SOURCE_MQTT}) is True)
+check("homewizard_local is enabled here too",
+      is_enabled({"meter_source": SOURCE_HOMEWIZARD}) is True)
 
 # The entity id SAFETY-01's firmware subscribes to, pinned by object_id.
 row = [s for s in SENSORS if s[0] == "p1_age"]
@@ -602,6 +1346,17 @@ check("with P1 on the age sensor IS announced",
 from app.main import Controller            # noqa: E402
 
 
+def _never():
+    """A stop Event these publish-only tests never set.
+
+    `stop` is a REQUIRED keyword argument (CFG-01): a Controller that cannot
+    stop itself used to be the default one, and on the late-refusal path that
+    meant a live process with no control loop and no exit. These cases only call
+    publish(), so any Event will do - but they may not skip it.
+    """
+    return asyncio.Event()
+
+
 class _Store:
     data = {}
 
@@ -624,18 +1379,80 @@ class _Pub:
 
 
 pub_off = _Pub()
-Controller({"meter_source": "off"}, None, _Store(), pub_off).publish()
+Controller({"meter_source": "off"}, None, _Store(), pub_off, stop=_never()).publish()
 check("with P1 off, p1_age is absent from the published payload",
       "p1_age" not in pub_off.last)
 check("...while the normal status keys are still published",
       "setpoint" in pub_off.last and "grid" in pub_off.last)
 
 pub_on = _Pub()
-Controller({"meter_source": SOURCE_HA}, None, _Store(), pub_on).publish()
+Controller({"meter_source": SOURCE_HA}, None, _Store(), pub_on, stop=_never()).publish()
 check("with P1 on, p1_age is published", "p1_age" in pub_on.last)
 check("...as a number, so has_state() becomes true only once we feed it",
       isinstance(pub_on.last["p1_age"], float))
 
+# ⚠️ And on ha_signed identically - this is the whole reason TEL-04 exists. The
+# age sensor is a hard prerequisite for the FW-01 flash, and it has to appear on
+# the transport that can actually read the meter in this house.
+pub_sig = _Pub()
+Controller({"meter_source": SOURCE_HA_SIGNED}, None, _Store(), pub_sig, stop=_never()).publish()
+check("with ha_signed selected, p1_age is published too",
+      "p1_age" in pub_sig.last and isinstance(pub_sig.last["p1_age"], float))
+
+# ⚠️ And on homewizard_local, where it is the one age FW-01 may actually
+# threshold - every other transport's age measures when the VALUE changed.
+pub_hw = _Pub()
+Controller({"meter_source": SOURCE_HOMEWIZARD}, None, _Store(), pub_hw, stop=_never()).publish()
+check("with homewizard_local selected, p1_age is published",
+      "p1_age" in pub_hw.last and isinstance(pub_hw.last["p1_age"], float))
+
+# --------------------------------------------------------------------------- #
+print("unchanged_s has somewhere an operator can read it")
+# ⚠️ The counter is deliberately NOT thresholded and NOT folded into the age -
+# at the converged -10 W this controller aims for, a 1 Wh register needs six
+# minutes to move, so any limit false-trips at the target operating point. That
+# refusal only holds up if a HUMAN can interpret the number instead, and DOCS.md
+# tells them "the transport tracks it as unchanged_s". Before this, nothing ever
+# read the transport object back: connected, polls, poll_errors and unchanged_s
+# were all write-only, and the documented signal existed nowhere an operator
+# could see it.
+
+
+def p1_rows(ctl):
+    """The P1 status line(s), or the exception that stopped checks() making one.
+
+    Same reason as built(): a status line that raises would abort the suite with
+    a traceback instead of reddening the check that names the rule.
+    """
+    try:
+        return [c["text"] for c in ctl.checks() if c["text"].startswith("P1 meter")]
+    except Exception as err:  # noqa: BLE001 - a raise here is itself the failure
+        print(f"       checks() raised {type(err).__name__}: {err}")
+        return err
+
+
+def _fed(source):
+    ctl = Controller({"meter_source": source}, None, _Store(), _Pub(), stop=_never())
+    ctl.p1.submit(make_sample(source, 350.0, 0.0, phases=1,
+                              ingest_mono=time.monotonic()))
+    return ctl
+
+
+hw_ctl = _fed(SOURCE_HOMEWIZARD)
+hw_src = HomeWizardLocalSource(None, hw_ctl.p1, "127.0.0.1")
+hw_src._note(hw_doc(350.0, l1=350.0))
+hw_ctl.p1_source = hw_src            # what amain() does once the transport exists
+rows = p1_rows(hw_ctl)
+check("the healthy P1 status line reports the transport's unchanged_s",
+      isinstance(rows, list) and len(rows) == 1 and "unchanged" in rows[0])
+
+# ⚠️ getattr, not attribute access: p1_source is None until amain() builds one,
+# and ha_dsmr/ha_signed/mqtt_p1 have no such counter at all. Reaching for it
+# directly would turn the whole status page into a 500 on every other transport.
+ha_rows = p1_rows(_fed(SOURCE_HA))
+check("...and the line is unharmed on a transport that has no such counter",
+      isinstance(ha_rows, list) and len(ha_rows) == 1 and "unchanged" not in ha_rows[0])
+
 print()
 if fails:
     print(f"{len(fails)} of {total} FAILED: {', '.join(fails)}")

goodwe_controller/test_validate.py

@@ -0,0 +1,318 @@
+"""Runnable check for the startup gate.  `python3 test_validate.py`
+
+Two halves, and the second is the one that matters. The first asserts that the
+three refusable configurations are refused. The second asserts that everything
+on validate.py's "deliberately not refused" list still STARTS - because the way
+a validator dies is not by missing a fault, it is by refusing something harmless
+until somebody deletes the call.
+"""
+
+import asyncio
+import sys
+
+from app.validate import (
+    ACTUATOR_WRITE_KEYS, FIRMWARE_INGEST_VETO_S, ConfigRefused, refuse,
+    validate_startup_config,
+)
+
+fails = []
+
+
+def check(name, cond):
+    print(f"  {'ok  ' if cond else 'FAIL'} {name}")
+    if not cond:
+        fails.append(name)
+
+
+def base(**over):
+    """A configuration that must start. Everything else is this, spoilt."""
+    o = {"setpoint_entity": "number.goodwe_setpoint", "max_w": 2000,
+         "soc_entity": "sensor.soc", "batt_entity": "sensor.batt",
+         "meter_source": "off"}
+    o.update(over)
+    return o
+
+
+def why(problems, needle):
+    return any(needle in p for p in problems)
+
+
+# --------------------------------------------------------------------------- #
+print("the baseline must start, or nothing below means anything")
+check("a good config with a 5000 W device is accepted",
+      validate_startup_config(base(), -5000, 5000) == [])
+check("...and with no device reachable yet, too",
+      validate_startup_config(base(), None, None) == [])
+
+# --------------------------------------------------------------------------- #
+print("1. max_w against the device's own rating")
+# ⚠️ THE ORIGINAL BUG. main.py used to log 'the device wins' and run anyway,
+# with write_setpoint() clamping, so the configured ceiling was never the real
+# one and the only evidence had scrolled off the log.
+p = validate_startup_config(base(max_w=8000), -5000, 5000)
+check("max_w above the device maximum is refused", len(p) == 1)
+check("...and the message names the configured value", why(p, "8000"))
+check("...and the device's value", why(p, "5000"))
+check("...and says which one wins", why(p, "THE DEVICE WINS"))
+check("max_w exactly at the device maximum is fine",
+      validate_startup_config(base(max_w=5000), -5000, 5000) == [])
+check("max_w under it is fine",
+      validate_startup_config(base(max_w=2000), -5000, 5000) == [])
+# The charge side is a separate rail and an asymmetric device is legal.
+p = validate_startup_config(base(max_w=4000), -2500, 5000)
+check("a max_w the device cannot take on the CHARGE side is refused too",
+      len(p) == 1 and why(p, "charge side"))
+check("...naming the device's floor", why(p, "-2500"))
+# ⚠️ Not guessed at: the entity may simply not have booted yet. run_control()
+# re-runs this the moment the real rating arrives.
+check("an unreachable device skips the range check rather than assuming",
+      validate_startup_config(base(max_w=8000), None, None) == [])
+check("a non-numeric max_w is refused",
+      why(validate_startup_config(base(max_w="lots"), -5000, 5000), "not a number"))
+
+# --------------------------------------------------------------------------- #
+print("2. an actuator to write to")
+# A controller with no actuator: write_setpoint() returns on the blank entity,
+# so no rating is read, no heartbeat is sent, layer 1 pins the inverter at 0 W,
+# and the add-on looks perfectly healthy the whole time.
+for blank in ("", "   ", None):
+    p = validate_startup_config(base(setpoint_entity=blank), None, None)
+    check(f"setpoint_entity {blank!r} is refused", len(p) == 1)
+check("...and the message says why it is dangerous rather than untidy",
+      why(validate_startup_config(base(setpoint_entity=""), None, None),
+          "heartbeat"))
+# specs §1.5: two writers on one actuator is not expressible in this schema.
+check("there is exactly one way to reach the actuator",
+      ACTUATOR_WRITE_KEYS == ("setpoint_entity",))
+
+# --------------------------------------------------------------------------- #
+print("3. a meter that can never read")
+# ⚠️ These predicates belong to p1.validate_meter_options(), which build_source()
+# also uses. Asserted here to prove the gate actually consults it - one entry
+# point, not two.
+check("meter_source off asks nothing of the P1 keys",
+      validate_startup_config(base(meter_source="off"), -5000, 5000) == [])
+check("homewizard_local with no p1_host is refused",
+      why(validate_startup_config(base(meter_source="homewizard_local"),
+                                  -5000, 5000), "p1_host"))
+check("...and with a host it is accepted",
+      validate_startup_config(base(meter_source="homewizard_local",
+                                   p1_host="192.168.2.250"), -5000, 5000) == [])
+check("a poll cadence at meter_max_age_s is refused at STARTUP, not just disabled",
+      why(validate_startup_config(base(meter_source="homewizard_local",
+                                       p1_host="m", meter_poll_s=30,
+                                       meter_max_age_s=30), -5000, 5000),
+          "meter_max_age_s"))
+check("ha_signed with no p1_net_entity is refused",
+      why(validate_startup_config(base(meter_source="ha_signed"), -5000, 5000),
+          "p1_net_entity"))
+check("a phase list disagreeing with meter_phases is refused",
+      why(validate_startup_config(base(meter_source="ha_signed",
+                                       p1_net_entity="sensor.n", meter_phases=3,
+                                       p1_phase_net_entities=["a", "b"]),
+                                  -5000, 5000), "phase-count"))
+check("mqtt_p1 with no topic is refused",
+      why(validate_startup_config(base(meter_source="mqtt_p1"), -5000, 5000),
+          "meter_mqtt_topic"))
+check("ha_dsmr with only half its entities is refused",
+      why(validate_startup_config(base(meter_source="ha_dsmr",
+                                       p1_import_entity="sensor.i"), -5000, 5000),
+          "p1_export_entity"))
+check("a misspelt meter_source is refused rather than silently ignored",
+      why(validate_startup_config(base(meter_source="ha_signd"), -5000, 5000),
+          "is not one of"))
+
+# --------------------------------------------------------------------------- #
+print("4. meter_max_age_s against the firmware's compile-time veto")
+# ⚠️ The schema allows int(5,300); the firmware's threshold is baked in at 30 s
+# and wins silently. Same shape as the max_w case: a configured bound overridden
+# by a lower layer, with nothing saying so.
+hw = dict(meter_source="homewizard_local", p1_host="m")
+p = validate_startup_config(base(**hw, meter_max_age_s=120), -5000, 5000)
+check("a meter_max_age_s above the firmware veto is refused", len(p) == 1)
+check("...naming the configured value", why(p, "120"))
+check("...naming the firmware's value", why(p, "30"))
+check("...and saying which one wins", why(p, "THE FIRMWARE WINS"))
+check("the tested pair 30/30 is accepted",
+      validate_startup_config(base(**hw, meter_max_age_s=30), -5000, 5000) == [])
+check("one second above it is refused",
+      validate_startup_config(base(**hw, meter_max_age_s=31), -5000, 5000) != [])
+# Below the veto the add-on gives up FIRST, which is fail-safe and visible on
+# its own status page. Only above is the silent case.
+check("below the veto is fine - the add-on being stricter is not a conflict",
+      validate_startup_config(base(**hw, meter_max_age_s=10,
+                                   meter_poll_s=4), -5000, 5000) == [])
+# ⚠️ Scope: meter_max_age_s is read by nothing but P1Ingest, and the veto keys
+# off a sensor only published when ingestion runs. With the meter off it governs
+# nothing, so refusing would be pure trivia.
+check("with meter_source off the number governs nothing and is not refused",
+      validate_startup_config(base(meter_source="off", meter_max_age_s=300),
+                              -5000, 5000) == [])
+check("the constant is the firmware's, not a rounded guess",
+      FIRMWARE_INGEST_VETO_S == 30.0)
+
+# --------------------------------------------------------------------------- #
+print("max_w must be a positive magnitude")
+# Schema-blocked on a real install, but validate_startup_config() is also
+# sim/inject.py's entry point and can be handed any dict at all.
+for bad in (0, -1, -2000):
+    p = validate_startup_config(base(max_w=bad), -5000, 5000)
+    check(f"max_w {bad} is refused", len(p) == 1 and why(p, "must be positive"))
+check("...and the message explains it would read as a trip, not a mistake",
+      why(validate_startup_config(base(max_w=0), -5000, 5000), "contradiction"))
+# ⚠️ SAFETY-02 changed what this case has to say, and the change is real rather
+# than bookkeeping: with a 1 W ceiling the default 300 W sign-disagreement
+# threshold is unreachable, so rule 5 refuses - correctly, because the watchdog
+# would report itself armed while being incapable of firing. What this check is
+# FOR is "a positive max_w is not itself a refusal", so it now names a sign
+# threshold the ceiling can actually reach, and the interaction gets its own
+# check below.
+check("the smallest sane max_w still starts",
+      validate_startup_config(base(max_w=1, sign_disagree_w=0.5), -5000, 5000) == [])
+check("...but that same 1 W ceiling with the DEFAULT sign threshold is refused",
+      why(validate_startup_config(base(max_w=1), -5000, 5000), "never fire"))
+
+# --------------------------------------------------------------------------- #
+print("what must NOT be refused - a validator that fires on trivia gets deleted")
+# DOCS.md: the arbiter's `supervised` limit still binds the wire to +-max_w, so
+# the only cost of the extra headroom is unwind latency after saturation.
+check("integrator_max_w above max_w warns but starts",
+      validate_startup_config(base(max_w=2000, integrator_max_w=9000),
+                              -5000, 5000) == [])
+check("integrator_max_w 0 (follow max_w) starts",
+      validate_startup_config(base(integrator_max_w=0), -5000, 5000) == [])
+# Fail-safe AND already a red NOT READY banner naming the entity: a refusal on
+# top of that adds nothing an operator can act on.
+check("a missing soc_entity is left to the readiness banner",
+      validate_startup_config(base(soc_entity=""), -5000, 5000) == [])
+check("a missing batt_entity likewise",
+      validate_startup_config(base(batt_entity=""), -5000, 5000) == [])
+# The transient case. ESPHome is routinely not up when the add-on boots, and
+# refusing here would turn a device that arrives late into a restart loop.
+check("a setpoint entity that is configured but not yet found starts",
+      validate_startup_config(base(), None, None) == [])
+check("meter_poll_s with thin but non-zero headroom starts",
+      validate_startup_config(base(meter_source="homewizard_local", p1_host="m",
+                                   meter_poll_s=20, meter_max_age_s=30),
+                              -5000, 5000) == [])
+
+# --------------------------------------------------------------------------- #
+print("the refusal must be legible as a refusal, not as a crash")
+p = validate_startup_config(base(max_w=8000, setpoint_entity=""), -5000, 5000)
+check("several problems are all reported, not just the first", len(p) >= 1)
+refuse(p)   # prints the banner; the eye is the assertion for its wording
+err = ConfigRefused(p)
+check("ConfigRefused carries every problem", err.problems == p)
+check("...and str() names one of them", str(err) == p[0])
+
+# --------------------------------------------------------------------------- #
+print("the LATE refusal, when the device only shows up after the gate has run")
+# ⚠️ This path had no test at all and no live demonstration - the review's
+# catch. ESPHome is routinely not up when the add-on boots, so hass.limits()
+# returns (None, None), the range checks are skipped, and run_control() is the
+# first place the device's real rating is ever known. Everything below is about
+# what happens when it turns out to conflict.
+from app.main import Controller            # noqa: E402
+
+
+class _LateHass:
+    """Reports the range only run_control() gets to see."""
+
+    def __init__(self, lo, hi):
+        self.lo, self.hi = lo, hi
+        self.writes = []
+
+    async def limits(self, entity):
+        return (self.lo, self.hi, 1.0)
+
+    async def number(self, *a, **k):
+        return 0.0
+
+    async def set_number(self, entity, value):
+        self.writes.append(value)
+        return True
+
+
+class _Store2:
+    data = {}
+
+    def set(self, *a):
+        pass
+
+
+class _Pub2:
+    enabled = False
+
+    def publish(self, *a, **k):
+        pass
+
+    def close(self):
+        pass
+
+
+def late(opts_over, lo, hi):
+    """Drive run_control() against a device that only reports (lo, hi) now.
+
+    ⚠️ Returns whether run_control() EXITED ON ITS OWN. That is the assertion
+    that matters: on a refusal it must return without entering the while loop,
+    and on a clean config it must not return at all. So the clean case is stopped
+    from outside after it has had time to write, rather than waited on - a
+    wait_for() here would just time out, which is the correct behaviour dressed
+    up as a failure.
+    """
+    async def go():
+        stop = asyncio.Event()
+        hass = _LateHass(lo, hi)
+        # A device narrower than the shipped 5000 W schema ceiling is exactly
+        # the case that cannot be reached through the Supervisor on the live
+        # install, so it is reached here instead.
+        c = Controller(base(**opts_over), hass, _Store2(), _Pub2(), stop=stop)
+        c.auto = True
+        task = asyncio.create_task(c.run_control())
+        for _ in range(30):                    # up to ~3 s
+            if task.done():
+                break
+            await asyncio.sleep(0.1)
+        exited = task.done()
+        if not exited:
+            c.stopping = True
+        await asyncio.wait_for(task, timeout=5)
+        return c, stop, hass, exited
+    return asyncio.run(go())
+
+c, stop, hass, exited = late({"max_w": 5000}, -3600.0, 3600.0)
+check("a device narrower than max_w, discovered late, is refused",
+      c.refused is not None and len(c.refused) == 1)
+check("...naming both values", why(c.refused, "5000") and why(c.refused, "3600"))
+check("...signalling amain to wind down", stop.is_set())
+check("...and returning instead of looping forever", exited)
+# The whole point: run_control() must not fall through into the while loop. A
+# single write here would mean it commanded the inverter under a config it had
+# just declared unusable.
+check("...having never entered the control loop, so it wrote nothing",
+      hass.writes == [])
+check("...and it is recorded in the event log an operator reads",
+      any("REFUSED" in e for e in c.events))
+
+# The same path when there is no conflict: it must NOT refuse, and it must
+# actually regulate - asserted by a write reaching the device, not by absence.
+c2, stop2, hass2, exited2 = late({"max_w": 2000}, -5000.0, 5000.0)
+check("a late device that agrees does not trip the re-check", c2.refused is None)
+check("...and the control loop runs, writing to the device", hass2.writes != [])
+check("...and does not signal a shutdown", not stop2.is_set() and not exited2)
+
+# ⚠️ THE FOOTGUN THE REVIEW FOUND. `stop` used to default to None, so this
+# construction was legal and the refusal path then returned into a live process
+# with no control loop, no exit and no further output.
+try:
+    Controller(base(), _LateHass(-5000.0, 5000.0), _Store2(), _Pub2())
+    check("a Controller with no stop Event is rejected at construction", False)
+except TypeError:
+    check("a Controller with no stop Event is rejected at construction", True)
+
+# --------------------------------------------------------------------------- #
+print()
+if fails:
+    print(f"{len(fails)} FAILED: " + "; ".join(fails))
+    sys.exit(1)
+print("all checks passed")

goodwe_controller/test_watchdog.py

@@ -0,0 +1,248 @@
+"""Runnable check for the sign-disagreement watchdog.  `python3 test_watchdog.py`
+
+Every case here is either a fault this must catch or a piece of NORMAL behaviour
+it must not mistake for one. The second list is the longer one on purpose: an
+alarm that fires on ordinary operation is worse than no alarm, because the next
+person switches it off.
+
+The headline validation is not here - it is `sim/replay_sign.py` in the infra
+repo, which drives this module over the two captured bus days. This file is the
+table-driven half: boundaries, timers, the latch, and the arming gate.
+"""
+
+import sys
+from datetime import datetime, timedelta, timezone
+
+from app.watchdog import SignWatchdog, SignWatchdogConfig
+
+fails = []
+T0 = datetime(2026, 8, 20, 15, 0, 0, tzinfo=timezone.utc)
+
+
+def check(name, cond):
+    print(f"  {'ok  ' if cond else 'FAIL'} {name}")
+    if not cond:
+        fails.append(name)
+
+
+def drive(samples, cfg=None, following=True):
+    """Feed (offset_s, commanded_w, grid_w) tuples. Returns (wd, trip_offset)."""
+    wd = SignWatchdog(cfg)
+    trip_at = None
+    for item in samples:
+        offset, cmd, grid = item[0], item[1], item[2]
+        f = item[3] if len(item) > 3 else following
+        if wd.evaluate(cmd, grid, f, T0 + timedelta(seconds=offset)) and trip_at is None:
+            trip_at = offset
+    return wd, trip_at
+
+
+def opposed(duration_s, step=5, cmd=-1000, grid=1500, following=True, start=0):
+    return [(start + t, cmd, grid, following)
+            for t in range(0, int(duration_s) + 1, step)]
+
+
+print("the fault it exists to catch")
+wd, at = drive(opposed(300))
+check("charging into an importing house trips", wd.tripped)
+check("and trips at 180 s, not before", at == 180)
+check("the reason names both signals", "-1000" in wd.reason and "+1500" in wd.reason)
+print(f"       e.g. {wd.reason!r}")
+
+wd, at = drive(opposed(300, cmd=2000, grid=-2000))
+check("discharging into an exporting house trips too", wd.tripped and at == 180)
+
+print()
+print("the boundaries")
+wd, _ = drive(opposed(600, cmd=-300, grid=1500))
+check("300 W exactly does NOT qualify (strictly greater)", not wd.tripped)
+wd, _ = drive(opposed(600, cmd=-301, grid=1500))
+check("301 W does", wd.tripped)
+wd, _ = drive(opposed(600, cmd=-1000, grid=300))
+check("a 300 W meter does not qualify either", not wd.tripped)
+wd, _ = drive(opposed(175))
+check("175 s of disagreement does not trip", not wd.tripped)
+wd, _ = drive(opposed(180))
+check("180 s does (>= hold_s)", wd.tripped)
+
+print()
+print("continuity - the rule that produced zero false positives on real data")
+broken = opposed(175) + [(180, -1000, -1500)] + opposed(175, start=185)
+wd, _ = drive(broken)
+check("179 s, one agreeing sample, then 175 s more: no trip", not wd.tripped)
+check("and the window really was reset", wd.disagree_since is not None)
+long_enough = broken + opposed(200, start=365)
+wd, _ = drive(long_enough)
+check("but a full 180 s after the reset does trip", wd.tripped)
+
+print()
+print("things that are NOT faults")
+# The load-step transient. Measured on the healthy capture: longest 30 s.
+wd, _ = drive(opposed(30) + [(35 + t, 800, 900) for t in range(0, 300, 5)])
+check("a 30 s load-step crossover does not trip", not wd.tripped)
+
+# SoC 10 %, Standby, declining a 1350 W discharge. The battery does nothing, so
+# the meter stays where it was and the command agrees with it.
+wd, _ = drive([(t, 1350, 1350) for t in range(0, 900, 5)])
+check("a battery refusing a discharge command cannot trip it", not wd.tripped)
+
+# A frozen meter drives command and reading into agreement, not disagreement.
+wd, _ = drive([(t, 800, 800) for t in range(0, 900, 5)])
+check("a frozen meter cannot trip it", not wd.tripped)
+
+# Maintenance grid charge: 2500 W of charge against an importing house, for
+# hours. Opposed, both huge - and entirely correct.
+wd, _ = drive(opposed(7200, cmd=-2500, grid=3000, following=False))
+check("two hours of maintenance grid charge does not trip", not wd.tripped)
+check("and the timer never even started", wd.disagree_since is None)
+
+wd, _ = drive([(t, -1000, None) for t in range(0, 900, 5)])
+check("a missing meter reading does not trip", not wd.tripped)
+wd, _ = drive(opposed(175) + [(180, -1000, None)] + opposed(600, start=185))
+check("a missing reading mid-window RESETS it rather than accumulating",
+      wd.tripped and wd.disagree_since is not None)
+wd, at = drive(opposed(175) + [(180, -1000, None)] + opposed(600, start=185))
+check("...so the trip lands 180 s after the gap, not after 180 s total",
+      at == 365)
+
+wd, _ = drive([(t, 0.0, 3000) for t in range(0, 900, 5)])
+check("a 0 W command is not a wrong-direction command", not wd.tripped)
+
+print()
+print("the latch")
+wd, _ = drive(opposed(200))
+check("tripped after the fault", wd.tripped)
+# The trip commands 0 W, which removes the command side of the comparison.
+for t in range(200, 900, 5):
+    wd.evaluate(0.0, 3000, True, T0 + timedelta(seconds=t))
+check("stays tripped once the command is zeroed", wd.tripped)
+for t in range(900, 1500, 5):
+    wd.evaluate(1000, 1000, True, T0 + timedelta(seconds=t))
+check("stays tripped even once everything looks healthy again", wd.tripped)
+wd.reset()
+check("reset() is the only way out", not wd.tripped and wd.disagree_since is None)
+check("and the reason is cleared with it", wd.reason == "")
+
+print()
+print("the thresholds are configuration, not constants")
+cfg = SignWatchdogConfig(min_w=800.0, hold_s=60.0)
+wd, at = drive(opposed(300, cmd=-1000, grid=1500), cfg=cfg)
+check("a 60 s hold trips at 60 s", wd.tripped and at == 60)
+wd, _ = drive(opposed(600, cmd=-700, grid=1500), cfg=cfg)
+check("an 800 W gate ignores a 700 W command", not wd.tripped)
+
+print()
+print("the configuration that would disarm it is refused")
+from app.validate import validate_startup_config  # noqa: E402
+
+base = {"setpoint_entity": "number.sp", "meter_source": "off",
+        "meter_phases": 1, "meter_max_age_s": 30}
+p = validate_startup_config({**base, "max_w": 2000, "sign_disagree_w": 300},
+                            -5000, 5000)
+check("300 W under a 2000 W ceiling is accepted", p == [])
+p = validate_startup_config({**base, "max_w": 2000, "sign_disagree_w": 2000},
+                            -5000, 5000)
+check("a threshold AT max_w is refused", len(p) == 1 and "never fire" in p[0])
+p = validate_startup_config({**base, "max_w": 500, "sign_disagree_w": 3000},
+                            -5000, 5000)
+check("a threshold above max_w is refused", len(p) == 1 and "never fire" in p[0])
+p = validate_startup_config({**base, "max_w": 2000, "sign_disagree_w": 1999},
+                            -5000, 5000)
+check("one watt under the ceiling is reachable, so accepted", p == [])
+
+print()
+print("end to end: the trip is COMMAND ZERO, not alarm-only")
+# ⚠️ THE FAULT INJECTED HERE IS A NEGATIVE GAIN, and that is not a contrivance -
+# it is the minimal faithful model of what this watchdog is for. The check
+# compares the loop's OUTPUT DIRECTION against the INPUT STATE it was regulating,
+# so what it detects is a loop whose two ends have become decoupled in sign: a
+# gain, a claim or a strategy with its polarity inverted, or an integrator so far
+# wound up that unwinding takes minutes. (Illusmart's was the last one: it
+# reached -14 768 W against a +-5000 W rail while writing once every 20-60 s, and
+# that arithmetic alone is 5-15 minutes of wrong-direction command.)
+#
+# `gain` is float(0.05,1.0) in the schema, so this is not a reachable
+# configuration - it is a stand-in for a code regression, which is the case a
+# unit test can actually hold the line on.
+import asyncio  # noqa: E402
+
+from app.main import Controller  # noqa: E402
+
+
+class _Hass:
+    def __init__(self):
+        self.writes = []
+
+    async def limits(self, entity):
+        return (-5000.0, 5000.0, 1.0)
+
+    async def number(self, entity, invert=False):
+        # A house importing 2000 W, steadily, whatever the battery does.
+        return {"sensor.grid": 2000.0, "sensor.soc": 50.0,
+                "sensor.batt": 0.0}.get(entity)
+
+    async def set_number(self, entity, value):
+        self.writes.append(float(value))
+        return True
+
+
+class _S:
+    data = {}
+
+    def set(self, *a):
+        pass
+
+    def get_time(self, *a):
+        return None
+
+
+class _P:
+    enabled = False
+
+    def publish(self, *a, **k):
+        pass
+
+    def close(self):
+        pass
+
+
+async def _e2e():
+    hass = _Hass()
+    opts = {"setpoint_entity": "number.sp", "meter_entity": "sensor.grid",
+            "soc_entity": "sensor.soc", "batt_entity": "sensor.batt",
+            "meter_source": "off", "max_w": 2000, "gain": -0.6,
+            "sign_disagree_w": 300, "sign_disagree_s": 1, "auto_start": True}
+    c = Controller(opts, hass, _S(), _P(), stop=asyncio.Event())
+    c.auto = True
+    c.dev_min, c.dev_max = -5000.0, 5000.0
+    seen_wrong_way = False
+    for _ in range(12):
+        await c.read_inputs()
+        await c.cycle()
+        if c.target < -300 and not c.sign_wd.tripped:
+            seen_wrong_way = True
+        await asyncio.sleep(0.25)
+    return c, hass, seen_wrong_way
+
+
+ctrl, hass, wrong_way = asyncio.run(_e2e())
+check("the broken loop really did command charge into an import first", wrong_way)
+check("the watchdog tripped", ctrl.sign_wd.tripped)
+check("the commanded value is 0 W", ctrl.target == 0.0)
+check("0 W actually reached the device", 0.0 in hass.writes)
+check("and it got there through the failsafe claim, not by accident",
+      "failsafe" in ctrl.reason)
+print(f"       status line: {ctrl.reason!r}")
+check("the status page says so in words",
+      any("SIGN-DISAGREEMENT FAILSAFE" in c["text"] for c in ctrl.checks()))
+check("the banner leads with it",
+      "FAILSAFE" in ctrl.status_payload()["banner"])
+check("MQTT reports the failsafe state", ctrl.sign_wd.tripped)
+check("it stays at 0 W on later cycles too",
+      hass.writes[-1] == 0.0 and hass.writes.count(0.0) >= 1)
+
+print()
+if fails:
+    print(f"{len(fails)} FAILED: {', '.join(fails)}")
+    sys.exit(1)
+print("all checks passed")