goodwe-addon/goodwe_controller/DOCS.md

GoodWe RS485 Controller

Drives a GoodWe ES/BP battery inverter over its RS485 meter bus: holds net grid exchange at zero, and runs a monthly battery maintenance cycle so the BMS can balance cells and recalibrate its coulomb counter.

Installers: read FIELD-GUIDE.md in the repository. It is not optional reading — it contains the commissioning gates and the failure modes.

Before you start

You need:

• A GoodWe ES / BP family inverter (AA55 / RS485 meter-bus generation)
• The vendor's meter-emulating controller disconnected from the bus
• A T-CAN485 (ESP32) flashed with firmware/goodwe-master.yaml
• A grid-power sensor already working in Home Assistant, updating every ~5–10 s

The safety model, in short

The inverter holds its last command forever — it has no meter-timeout. So:

• The ESP32 commands 0 W if this add-on stops refreshing for ~30 s, and keeps commanding it.
• This add-on commands 0 W when its inputs go missing, when you stop control, and when it shuts down.
• The optional RS485 e-stop is the only thing that covers this machine dying. Without it, a failed host leaves the battery latched at its last command until someone intervenes.

If anything looks wrong: stop the add-on. That commands 0 W and the hardware holds it there.

Configuration

Sources

option	required	meaning
meter_entity	yes	Net grid power. Positive must mean importing
meter_invert		Flip the sign if the meter reports the other way
soc_entity	yes	Battery state of charge — use the ESP32's own read
batt_entity	yes	Battery power — again the ESP32's read, + = discharging
batt_invert		Flip if needed
setpoint_entity	yes	The ESPHome number.*_goodwe_setpoint_w

Use the ESP32's readings rather than the inverter's cloud or dongle sensors: those serve cached values, and a stale reading here ends the maintenance charge phase having charged nothing.

P1 meter ingestion

meter_entity above expects one signed sensor, which usually means a template someone wrote by hand. A Belgian P1 meter does not publish one: it publishes two unsigned registers, consumption and injection. Setting meter_source moves that subtraction into the add-on, where it is done once and tested, and replaces meter_entity entirely.

option	default	meaning
meter_source	off	off keeps meter_entity. ha_dsmr subscribes to the DSMR integration over the HA WebSocket; mqtt_p1 reads a topic
meter_phases	1	1 or 3. Must match the telegram, or every telegram is rejected and logged
meter_max_age_s	30	Beyond this the reading is stale: grid power reads as missing, and the existing failsafe commands 0 W
meter_mqtt_topic		mqtt_p1 only
p1_import_entity		The unsigned consumption sensor. Do not point this at a signed template
p1_export_entity		The unsigned injection sensor
p1_phase_import_entities	[]	L1..L3, in order. Needed for the capacity-tariff peak on a three-phase connection
p1_phase_export_entities	[]	L1..L3, in order

There is no fallback to an inverter-side power figure, deliberately. The inverter's own AC power tracks its battery almost perfectly and the real meter hardly at all, so a controller that failed over to it would be regulating against its own output while looking healthy.

The mqtt_p1 payload is one JSON object per telegram, and the schema is strict — a key it does not recognise is a telegram from something other than what was tested, and guessing a key here means guessing a kilowatt:

{"import_w": 1234.0,
 "export_w": 0.0,
 "phases": [{"import_w": 500, "export_w": 0},
            {"import_w": 400, "export_w": 0},
            {"import_w": 334, "export_w": 0}],
 "timestamp": "2026-08-24T18:00:05+02:00"}

phases and timestamp are optional; timestamp must carry a UTC offset. Where it is present it is used for the age, which is what stops a retained message replayed on reconnect from presenting a ten-minute-old reading as current.

sensor.p1_sample_age_s

Published over MQTT discovery whenever a broker is available: seconds since the newest accepted telegram, refreshed every second rather than only when a telegram lands. The ESP32's stale-input watchdog subscribes to this exact entity id, so do not rename it.

The reason it is recomputed against the clock is that Home Assistant only pushes a state when the state changes. A meter sitting at a genuinely constant reading emits nothing, which is indistinguishable — to anything watching the value — from a meter that has died. Watching the age instead separates the two: it climbs when telegrams stop and resets when they arrive, whatever the reading says.

Control

option	default	meaning
max_w	2000	Hard limit on what may be commanded. Start low, raise after commissioning
gain	0.6	Correction per cycle. At the limit — do not raise
slew_w	1000	Maximum change per cycle
deadband_w	15	Ignore errors smaller than this
target_grid_w	-10	What the meter should rest at. Negative = a slight export
step_w	10	Quantisation
saturation_w	500	Divergence that counts as "the inverter is at a limit"
saturation_cycles	3	How many consecutive cycles before freezing. A cycle is one changed meter reading, not a fixed period - see the note below. Do not set to 1
integrator_max_w	0	Bound on the loop's accumulator, and 0 means "same as max_w". Caps how much stale error can be waiting to unwind when the sign flips. Do not raise it above max_w - the output clamp already bounds what is commanded, so the only thing extra headroom buys is more cycles of wrong-direction power after every saturation event. Lowering it below max_w is the useful direction
heartbeat_s	10	Refresh interval; must stay well under the firmware watchdog
stale_input_s	15	How long inputs may be missing before commanding 0 W
auto_start	false	Start controlling on boot (only after commissioning)

Saturation is counted in cycles, not seconds

The specification states the saturation window as "> 10 s". This add-on counts cycles instead, and that is a deliberate, accepted deviation rather than an oversight - the acceptance criterion is not met as literally written.

A cycle here is one changed meter reading: the controller only runs the loop when the meter value differs from the previous poll. At the reference P1's ~5 s update rate the default of 3 cycles is usually around 15 s, but there is no guaranteed wall-clock window - a meter that repeats the same value stalls the counter for as long as it repeats.

Two reasons that is acceptable:

• the control law is a pure function with no clock, which is what makes it testable without hardware, and a seconds-based window would have to live in the controller;
• a stalled counter is a detection-latency limit and not a runaway risk. The condition that stalls it - an unchanging meter - stops the whole loop, so nothing accumulates while it is stalled.

If a guaranteed window matters on your site, raise saturation_cycles for a fast meter, and treat the figure as "N meter updates" rather than "N seconds".

Why target_grid_w is not zero

The deadband is a one-way ratchet: any resting point inside it holds until something disturbs it. Import and export are separate registers on the meter, so a rest point of +14 W is billed for every second it holds and no amount of export cancels it - 14 W all day is 0.34 kWh.

Biasing the target below zero moves that residue into the export register, which is not billed. The resting band becomes target ± deadband, so:

target_grid_w	resting band	worst billed leak	export given away
0	-15 … +15 W	~15 W (0.35 kWh/day)	none
-10	-25 … +5 W	~5 W (0.12 kWh/day)	~10 W
-15	-30 … 0 W	none	~15 W (0.36 kWh/day)

Set it to -deadband_w if injection is worth nothing to you and you would rather give the energy away than buy it back. Set it to 0 if you are paid properly for export, or if you are debugging and want the loop centred.

⚠️ This is a billing knob, not a speed knob. If import is arriving in bursts rather than as a trickle, the cause is tracking lag, and this will not help - see "Why the tuning is what it is".

Maintenance

option	default	meaning
maintenance_enabled	false	Enable the monthly cycle
maintenance_interval_days	28	Minimum gap between cycles
maintenance_start_hour	10	Hour of day a due cycle begins
maintenance_discharge_w	2500	Drain rate (exports the surplus)
maintenance_charge_w	2500	Charge ceiling, capped again by peak headroom
maintenance_soc_floor	11	Drain target — stay just above the inverter's own floor
maintenance_soc_target	99	Charge target
maintenance_hold_min	120	Hold at full so the BMS can balance

Tariff (all optional)

option	meaning
peak_forecast_entity	Quarter-hour demand forecast, for capacity-tariff markets. Empty = no cap
peak_cap_w	The site's capacity-tariff target
price_now_entity, price_avg_entity	Dynamic tariff. Empty = never force a paid grid top-up

On a capacity-tariff site the maintenance charge is capped by the headroom left under peak_cap_w, and if the forecast goes over the cap the charge-only clamp is dropped so the battery can shave the peak instead. Money outranks the maintenance schedule.

Site

option	meaning
estop_fitted	Whether the RS485 e-stop is installed. Drives the warning banner
log_level	trace/debug/info/warning/error

The Web UI

The ingress panel shows live values, why the controller is commanding what it is, and a Commissioning checklist that names any problem in words. It also carries the three buttons: start/stop control, force a maintenance cycle, and abort one.

Status entities

If an MQTT broker is available the add-on publishes setpoint, grid power, battery power, state of charge, maintenance phase and controller status by MQTT discovery. This is observability only — the controller works fine without a broker, and MQTT problems can never affect control.