UX-11 review: restored stops log their figures to events, the quiet-meter WARNING is rate-limited

- After a restart, each restored stop (direction per inverter and site,
  delivery, circulation) also writes its saved reason to the action log.
  log_level defaults to info and events starts empty, so the DEBUG
  evidence alone left the figures only in state.json.
- A flapping meter (ha_signed under a flat load, 42-97 s between changes)
  logs at most one WARNING/INFO pair per 10 minutes, with the episodes in
  between at DEBUG.
- LONG_LINE_OK refuses any key whose text is a safety reason.
- test_watchdog keeps the byte pin beside the meaning pin, since the text
  did not change.
- DOCS says the DEBUG line needs log_level debug.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

goodwe_controller/test_messages.py

@@ -1227,7 +1227,9 @@ check(f"UX-11: no WARNING+ line runs over {LINE_WORDS} words as logged, except "
       f"the {len(LONG_LINE_OK)} listed families, and none of them is a safety "
       f"reason (cap {LONG_LINE_CAP})",
       len(LONG_LINE_OK) <= LONG_LINE_CAP
-      and not any("reason_code" in k for k in LONG_LINE_OK))
+      and not any("reason_code" in k
+                  or TEXT.get(k) in SAFETY_REASONS.values()
+                  for k in LONG_LINE_OK))
 check(f"...and every listed family still runs long, so the list only shrinks "
       f"(no longer long: {sorted(set(LONG_LINE_OK) - _long_seen)})",
       set(LONG_LINE_OK) <= _long_seen)
@@ -1397,6 +1399,7 @@ import logging                                                    # noqa: E402
 from app import hass as _hass, p1 as _p1, validate as _validate, web as _web  # noqa: E402
 from app.arbiter import Claim                                     # noqa: E402
 from app.main import Controller, why_key                          # noqa: E402
+from app import main as _main                                    # noqa: E402
 
 
 class _Rec(logging.Handler):
@@ -1695,7 +1698,12 @@ def _meter_at(age_s):
 
 
 def _quiet_episodes():
-    for age in (1, 40, 45, 50, 1, 2, 60, 65):
+    # Two quiet episodes close together, then a third 10 minutes on.
+    for age in (1, 40, 45, 50, 1, 2, 60, 65, 1):
+        _meter_at(age)
+        asyncio.run(_c.read_inputs())
+    _c._meter_quiet_warned -= _main.METER_QUIET_REPEAT_S
+    for age in (40, 45, 1):
         _meter_at(age)
         asyncio.run(_c.read_inputs())
 
@@ -1704,9 +1712,13 @@ _mq = [r for r in _captured("goodwe", _quiet_episodes)
        if "meter" in r.getMessage().lower()]
 _mq_warn = [r.getMessage() for r in _mq if r.levelno == logging.WARNING]
 _mq_info = [r.getMessage() for r in _mq if r.levelno == logging.INFO]
+_mq_dbg = [r.getMessage() for r in _mq if r.levelno == logging.DEBUG]
 check(f"a meter that goes quiet logs one WARNING per episode, not per cycle, "
-      f"and one INFO when readings return ({_mq_warn}, {_mq_info})",
-      len(_mq_warn) == 2 and _mq_info == ["Meter readings are back."]
+      f"and one INFO when readings return, and a flapping meter at most one "
+      f"pair per {_main.METER_QUIET_REPEAT_S:.0f} s ({_mq_warn}, {_mq_info}, "
+      f"{_mq_dbg})",
+      len(_mq_warn) == 2 and _mq_info == ["Meter readings are back."] * 2
+      and len(_mq_dbg) == 2
       and _mq_warn[0] == "No meter reading for over 30 seconds, so control "
                          "waits and then sets the battery to 0 W."
       and len(words(_mq_warn[0])) <= LINE_WORDS)
@@ -1763,6 +1775,13 @@ check("...each ERROR line at start is one plain sentence with the code, at "
       and any(m.endswith(f": {messages.NO_REASON_SAVED}.") for m in _rs_err))
 check("...and the saved text, figures and all, is on a DEBUG line beside it",
       all(any(t in m for m in _rs_dbg) for t in _OLD.values()))
+# UX-11 review: `log_level` defaults to info and `events` starts empty, so the
+# saved figures also go on the action log, where `status` shows them.
+_rs_ev = _restart[0].events if _restart else []
+check(f"...and in the action log, which an installer reads at the default "
+      f"log level ({len(_rs_ev)} events)",
+      all(any(t in e for e in _rs_ev) for t in _OLD.values())
+      and any(e.endswith(messages.NO_REASON_SAVED) for e in _rs_ev))
 
 # UX-11 item 4: the action log's clamp count and the shadow-off entry.
 _main_src = (APP / "main.py").read_text(encoding="utf-8")